User manual MAYTAG MDE3706AGW

[. . . ] · If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency or the gas supplier. FIRE HAZARD Do not place into your dryer items that have been spotted or soaked with vegetable oil or cooking oil. Even after being washed, these items may contain significant amounts of these oils. [. . . ] Plastic articles such as caps or babies waterproof napkin covers should not be dried with heat in the dryer. Keep the area around the exhaust opening and surrounding areas free from lint accumulation, dust and dirt. The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel. Never connect the appliance cord to a power supply that is not grounded adequately and in accordance with local and national codes. Do not sit or stand on top of the dryer. Important Safety Notice & Warning Users of a gas appliance are hereby warned that the burning of gas can result in low­level exposure to some of the listed substances, including benzene, formaldehyde, and soot, due primarily to the incomplete combustion of natural gas or liquid petroleum (LP) fuels. Exhaust ducts should be kept free of obstructions and properly exhausted dryers will minimize exposure. WARNING Gas leaks may occur in your system and result in a dangerous situation. Gas suppliers recommend you purchase and install an UL approved gas detector. Install and use in accordance with the manufacturer's instructions. Note: Because of continuing product improvements, we reserve the right to change specifications without notice. For complete details, see the Installation Instructions packed with your product before selecting cabinetry, making cutouts or beginning installation. SAVE THESE INSTRUCTIONS 2 Using the Controls STEP 1 STEP 3 Select Temperature In order to select the correct temperature, turn the Temperature control to one of four choices; Regular, Medium (select models), Delicate or Air Fluff. DRYER TEMPS Regular Medium (select models) Delicate LOAD TYPE Sturdy cottons or labels marked Tumble Dry. For wrinkle-free/permanent press synthetics, lightweight cottons labeled Tumble Dry Medium. Use the Time Dry/Air Fluff cycle. Select Cycle To select a cycle, rotate the control dial to the desired setting. When using an Auto Dry cycle, the control dial should point between More Dry and Less Dry for most loads. Loads of larger or bulkier size may require the More Dry setting to completely dry the load. The Less Dry setting is best suited for lightweight fabrics or for leaving some moisture in the clothing at the end of the cycle. Auto Dry Regular The Auto Dry Regular cycle is designed to dry most cottons and linens. At the end of the cycle, the clothes are cooled for approximately 10 minutes to reduce wrinkling. Air Fluff Auto Dry Wrinkle Control The Auto Dry Wrinkle Control cycle is designed to dry wrinkle-free cottons, synthetic fabrics, double knits and permanent press fabrics automatically. At the end of the cycle, the clothes are cooled for approximately 25 minutes to reduce wrinkling. STEP 2 Select Options End of Cycle Signal (select models) When the cycle is complete, a signal will sound. 3 Cycles and options may vary by model. Time Dry/Air Fluff This cycle can be used to regulate the drying time. For timed drying, turn the control dial until the pointer points to the proper time setting in the Time Dry/Air Fluff cycle. STEP 4 Push the Control Dial in to Start Push the control dial in to start the dryer. The dryer door must be closed for the dryer to start. Note: Using the Air Fluff temperature setting will require a longer drying time. Note: The dial can be turned in either direction to select a cycle. Once started, the dial will not advance at a specific rate during the Auto Dry cycles. Toward the end of the cycle (when the load begins to dry), the dial will advance at a more regular rate and much more quickly. [. . . ] · It is normal for the dryer to hum due to the high velocity of air moving through the dryer drum and exhaust system. · This is normal operation for an Auto Dry cycle, especially at the beginning of cycle. The rate of advancement will be slow at the beginning of the cycle because there is more moisture in the load. As the load becomes more dry, the control knob will advance more quickly. [. . . ]