User manual MAYTAG MDE1100AES

[. . . ] ATTENTION Other important remarks Important safety information The following advice and warnings have been drawn up, so that you may avoid both misusing the drying cabinet and the risk of unnecessary accidents. So read the following through very carefully before installing and using the drying cabinet. Do not dry articles of clothing or similar items which have just been treated with petrol or some other volatile and inflammable agent. Keep an eye on children when they are in the immediate vicinity of the cabinet. [. . . ] (For the markets where such an article is included) Do not assemble the ventilation duct valve inside the drying cabinet. 3 1 1. Ventilation duct valve 2 The drying cabinet permanently installed and connected to the evacuation duct 11 Installation Unpacking WARNING The cabinet can easily tip over since it is not yet solidly screwed into place. WARNING The packing material such as plastic or frigolite should be kept out of children´s way. Take off all the packing material; do not use a sharp tool which could damage the product. Check that the drying cabinet has not been damaged during transportation. The distributor should be notified of any damage during transportation within 7 days. After unpacking, check that the drying cabinet is free from defects. The distributor should immediately be notified of any damage, defects or even missing parts. Check that all the safety devices used for transportation have been removed before the drying cabinet is connected. Complete delivery includes The cabinet with the fan unit Flexible hose for ventilation (only certain markets) Exhaust collar with 2 attachment screws Draft stabilizer (only certain markets) Attachment screws (2 screws, washers and protective caps) for firmly fixing the cabinet to the wall Allen wrench and protective caps for the adjustable feet The Use and Care Guide for installation and utilisation Recommended tools Bubble level Tape measure Hand drill Screwdriver (Phillips) An 8 mm diameter drill bit Pencil Protective gloves (if supplied) 12 Placing the door the other way round The door can be hung on its hinges on the left or the right. Disengage the hinge pin of the bottom hinge (1) and lift the door off. Take off the plastic plug and press it right down on to the bottom hinge on the opposite side. Disengage the hinge pin of the upper hinge (2) and place it on the opposite side. Completely unscrew the glove hangers on the inside of the door and turn them completely around. Rotate the door, fit it into place and fix it firmly by means of the lower hinge pin (1). 2 1 13 Horizontal adjustment 1. Minimum air gap 10 mm between drying cabinet and mounting unit (above and behind the drying cabinet) Tape measure Assembly holes Drying cabinet back wall Wall behind the drying cabinet 3 4 2. 5. 5 15 7. Fix the two parts of the wooden strip in place using two screws, each of them screwed into the wall behind the drying cabinet, so that they correspond with the holes marked as in point 4. Take off the adhesive tape holding the door and check that the wooden strip is in place on the back wall of the drying cabinet. Also check that the front part of the drying cabinet fits well into the custon cabinetry. . Adjust the position of the drying cabinet horizontally according to the instructions in the section "Horizontal adjustment" and screw the drying cabinet firmly down into place according to the instructions in the section "Mounting" on page 14. 8. 1 3 4 2 ~150 mm The custom cabinetry with assembled wooden strip, divided into two parts, to allow free passage of air 1. 4. Attachment screws Hole marking Air flow Wooden strip (in two parts) ATTENTION Check that the wooden strips are properly and firmly in place in the back wall and also that the assembly screws do not obstruct the assembly holes in the drying cabinet. 16 Ventilation connection If the drying cabinet is installed in a custom cabinetry, fit the exhaust collar through the vent opening in the upper part of the cabinetry when the drying cabinet is moved to its final location. Place the exhaust collar over the hole in the drying cabinet's top plate, align the screw holes and screw the exhaust collar into place. Connect the vent pipe if the drying cabinet is built in, or press the supplied (only certain markets) flexible hose into place. The exhaust collar is designed to be screwed in place with two screws to the drying cabinet's top plate. There are predrilled holes in the exhaust collar and top plate. 1 1. Exhaust collar Electrical connection Consult the earlier section 'Electrical requirements', on page 8. 17 Final check 1. [. . . ] The temperature limiter has been Turn the time switch back to '0' and wait 30 minutes. try again by activating the temperature selector knob and, after that, start the fan by turning on the time swith. The temperature limiter is faulty Contact Customer Service. 23 Service Before you contact customer service, you should find out the designation of the model, its type and its serial number. The designation of the model is inscribed on the cabinet control panel. [. . . ]