User manual MAYTAG MAH7550AGW

[. . . ] i C O N T E N T S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G E N E R A L I N F O R M A T I O N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 PRE-INSTALLATION REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 U N C R A T I N G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] around the lip of the outer tub cover and place the spring at the 11:00 o'clock position, just left of the top rib of the outer tub cover. Hook the end of the spring over the nearest tub cover clip to hold the spring and wire in position for final hookup to the other end of the wire loop. outer tub spring, grasp the hook end of the spring and apply pressure on the clamp wire into the door boot. If the wire loop becomes bent, the result will be a potential leak upon replacement of the boot seal onto the outer tub cover. OUTER TUB COVER The outer tub cover has a gasket seal embedded in the outer flange of the cover to seal the cover to the outer tub. The cover is secured to the outer tub by means of twelve (12) locking clips evenly spaced around the perimeter of the cover. When the outer tub cover is removed, access to the sump area and the front injector flume is possible. REMOVAL 1 Disconnect power to the unit. Remove the front panel, top cover and front shroud (See Front Panel, Top Cover, and Front Shroud Removal). This exposes the sump area on the floor of the outer tub and the water injector flume on top of the outer tub. 16008373-01 SECTION 7. OUTER TUB & SPINNER ASSEMBLY © 1998 Maytag Corporation 7-2 REMOVAL 1 Disconnect power to the unit. Remove the front panel, top cover, front shroud, outer tub cover and rear baffles (See Front Panel, Top cover, Front Shroud, Outer Tub Cover and Rear Baffle Removal). Figure 7-2 SPIN BASKET ASSEMBLY w/BALANCE RING The balance ring is securely fastened to the spin basket and cannot be obtained as a separate repair part. The balance ring is filled with a calcium chloride solution and baffles. 3 To separate the spinner tub support from . It is comprised of a stainless steel seal face positioned on the tub support shaft, which mates with a rubber gasket. Grease on the face of the rubber gasket provides lubricant for the steel seal face. The steel seal face provides the rotating seal surface against the circular rubber ribs in the face of the rubber seal. This makes for three rib contacts at various diameters, providing three seals. ner (See Spinner Tub Support Removal). Figure 7-9 4 Reach inside the outer tub bearing area . shaft into the outer tub and insert the shaft through the seal in the rear of the outer tub until the spinner support shaft seats into place. This will draw the shaft and seals into proper alignment. Figure 7-8 3 With a flathead screwdriver, pry the seal . OUTER TUB & SPINNER ASSEMBLY © 1998 Maytag Corporation 7-6 REMOVAL OF UPPER WEIGHT OUTER TUB ASSEMBLY 1 Disconnect power to the unit. The outer tub assembly is suspended from two springs positioned toward the upper front of the cabinet and supported in the rear by two struts which are secured to the base frame. Two counter weights are mounted to the outer tub from above and below the tub. The aluminum bearing housing retains both inner and outer bearings for the spinner tub support shafts. [. . . ] Pressurization in the vertical outlet of the pump actuates the pressure switch and determines proper fill levels. Teardown & Wiring Information ©2001 Maytag Appliances Sales Company REMOVAL 1. Remove the rear access panel or the front panel to access the pressure switch. Press in the locking tabs on the back of the pressure switch and pivot the pressure switch off the pump bracket. [. . . ]