User manual MAXTOR VIKING II JUMPERS

[. . . ] Viking II: Wide-Low Voltage Differential SCSI Jumper Settings Jumper Settings The following describes the jumper options and settings available on the Maxtor® VikingTM II disk drive. For more detail on jumper definitions; please refer to the jumper definition section. [. . . ] The termination power option setting is located on the printed circuit board at the rear of the drive and is near the SCSI cable connector. 2 of 2 Viking II: Wide-Low Voltage Differential SCSI Jumper Settings Pin 1 3 5 7 9 11 13 15 17 19 Signal A0 A1 A2 A3 SE LED Cathod (Neg) Wait Spin Spin Delay RSVD2 NC Pin 2 4 6 8 10 12 14 16 18 20 Signal logic_gnd logic_gnd logic_gnd logic_gnd logic_gnd LED Anode (Pos) logic_gnd logic_gnd logic_gnd logic_gnd 3 of 3 Viking II: Wide-Low Voltage Differential SCSI Jumper Settings Pin 1 3 5 7 9 11 Signal A0 A1 A2 A3 SE +5VDC out Pin 2 4 6 8 10 12 Signal XTFAULT logic_gnd logic_gnd LED CATHOD logic_gnd NC SCSI ID Settings The following table identifies the various SCSI ID values and the jumper positions required to set them. Drive ID ID 0 ID 1 ID 2 ID 3 ID 4 ID 5 ID 6 ID 7 ID 8 A0 OFF ON OFF ON OFF ON OFF ON OFF A1 OFF OFF ON ON OFF OFF ON ON OFF A2 OFF OFF OFF OFF ON ON ON ON OFF A3 OFF OFF OFF OFF OFF OFF OFF OFF ON 4 of 4 Viking II: Wide-Low Voltage Differential SCSI Jumper Settings ID 9 ID 10 ID 11 ID 12 ID 13 ID 14 ID 15 ON OFF ON OFF ON OFF ON OFF ON ON OFF OFF ON ON OFF OFF OFF ON ON ON ON ON ON ON ON ON ON ON 5 of 5 Viking II: Wide Single-Ended SCSI Jumper Settings Jumper Settings The following describes the jumper options and settings available on the Maxtor® VikingTM II disk drive. For more detail on jumper definitions; please refer to the jumper definition section. The Maxtor Viking II was developed by Quantum Corporation prior to its merger with Maxtor. LVD Disable (SE)1 Enable termination Disable termination TE jumper on TE jumper off* Termination Power (TP) Enable termination power Disable termination power TP jumper on* TP jumper off SCSI ID (A3, A2, A1, A0) Set drive SCSI ID See ID settings table below 1 of 1 Viking II: Wide Single-Ended SCSI Jumper Settings Wait Spin (WS) Enable wait spin Disable wait spin WS jumper on WS jumper off* Spin Delay (SD) Enable spin delay Disable spin delay SD jumper on SD jumper off* Write Protect (RSVD2) Write Protection Write Enable * Indicates default jumper setting RSVD2 jumper on RSVD2 jumper off* Jumper Locations The Viking II wide disk drive has two locations where user configurable jumpers are found. The primary jumper block (Front option connector J3) for the Viking II wide drive is found on the front edge of the disk drive printed circuit board. Using these jumper pins you can establish the various drive configuration options. The secondary option jumper block provides an alternate method for setting primary drive features. The alternate jumper block is located at the rear of the drive and is incorporated into the SCSI cable connector. The termination and termination power option setting, only available on SE (non-differential) versions, is locate d on the printed circuit board at the rear of the drive and is near the SCSI cable connector. 2 of 2 Viking II: Wide Single-Ended SCSI Jumper Settings Pin 1 3 5 7 9 11 13 15 17 19 Signal A0 A1 A2 A3 TE LEDPWR Wait Spin Spin Delay RSVD2 NC Pin 2 4 6 8 10 12 14 16 18 20 Signal logic_gnd logic_gnd logic_gnd logic_gnd logic_gnd LEDPWR logic_gnd logic_gnd logic_gnd logic_gnd 3 of 3 Viking II: Pin 1 3 5 7 9 11 Signal A0 A1 A2 A3 +5VDC out Pin 2 4 6 8 12 Signal XTFAULT logic_gnd logic_gnd LED CATHOD logic_gnd NC Wide Single-Ended SCSI Jumper Settings Enable Termination 10 SCSI ID Settings The following table identifies the various SCSI ID values and the jumper positions required to set them. Drive ID ID 0 ID 1 ID 2 ID 3 ID 4 ID 5 ID 6 ID 7 ID 8 ID 9 ID 10 ID 11 ID 12 ID 13 ID 14 ID 15 A0 OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON A1 OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON A2 OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON A3 OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON 4 of 4 Viking II SCSI Jumper Settings Jumper Settings The following describes the jumper options and settings available on the Maxtor® VikingTM II SCA disk drive. For more detail on jumper definitions; please refer to the jumper definition section. The Maxtor Viking II was developed by Quantum Corporation prior to its merger with Maxtor. LVD Disable (SE) Enable Single Ended operation * Indicates default jumper setting SE jumper on Enable auto switch between Single Ended or LVD operation SE jumper off * Jumper Locations The Viking II SCA disk drive has only one location where user configurable jumpers are found. The jumper block for the Viking II SCA drive is found on the disk drive printed circuit board near the SCA cable connector. 1 of 1 Viking II SCSI Jumper Settings The Viking II SCA drive has only the single jumper position referenced above. [. . . ] This configuration is determined by the system at start-up or by user definition during system setup. Contact your system manufacturer for details on setting SCSI ID. 2 of 2 [. . . ]