User manual MAXTOR U6 INSTALLATION REV A

[. . . ] When using the alternate capacity jumper, Disk Manager software is required to achieve the drive's full capacity. To run DiscWizard: Download the software from www. seagate. com, and follow the online instructions to complete the installation. If you cannot run DiscWizard, follow the instructions on this installation sheet to install and configure your drive. Attaching Cables and Mounting the Drive 1. Attach one end of the drive interface cable to the interface connector on your computer's motherboard (see your computer manual for connector locations). Align pin 1 on the motherboard connector with pin 1 on your drive connector. [. . . ] Save and exit the system setup program. Setting the Jumpers Options jumper block Master or single drive Drive is slave Master with non ATAcompatible slave Cable select Limit drive capacity >32 Gbytes = 32 Gbytes <32 Gbytes = 2. 1 Gbytes 7 5 31 Refer to the jumper settings on your drive label to configure the drive for your system. Jumper settings can also be accessed online from our Web site at www. seagate. com BIOS Settings Drive Model ST330610A ST315312A ST310213A Formatted Gbytes 30. 6 15. 3 10. 2 Total Sectors* 59, 765, 625 29, 882, 812 20, 005, 650 8 6 4 2 Circuit Board *One sector equals 512 bytes. Preparing the Drive with Disk Manager or DiscWizard Installing a Single Drive If you are installing a single drive, we recommend using Disk Manager to automatically partition and format your drive. During the download, the Diskette Creator creates a bootable diskette. Insert your bootable Disk Manager diskette and follow the instructions. Boot your computer from the Windows Me, Windows 98 or Windows 95 startup diskette with the Windows CD loaded. At the prompt, type setup. For more information, see the earlier section on the Ultra ATA/100 requirements. In addition, some legacy BIOS may cause a hang due to the large drive capacity. Consider using the alternate capacity jumper if it is available on your drive model. Use the alternate capacity jumper if your computer does not support higher capacity drives. The jumper will limit the 80, 60 and 40-Gbyte drive capacities to 32 Gbytes. If these steps do not solve the problem, contact your dealer or visit http://seatools. seagate. com to download SeaTools disc diagnostics software and more troubleshooting advice. Seagate Support Services Internet For online information about Seagate products, visit www. seagate. com or e-mail your disc questions to: DiscSupport@Seagate. com. Installing a Slave Drive If you are installing a second drive, or slave, to your system, use the DiscWizard software available at www. seagate. com. If you do not want to install your drive using either DiscWizard or Disk Manager, see "Standard Microsoft Installation" below to partition and format your drive. Technical Support If you need further help installing your drive, first consult your dealer. Dealers are familiar with their unique system configurations and can help you with system conflicts and other technical issues. If you need additional help, you can talk to a Seagate technical support specialist. Before calling, note your system configuration and drive model number. Africa Australia Austria Belgium Denmark France Germany Hong Kong Indonesia Ireland Italy Malaysia Middle East Netherlands New Zealand +31-20-316-7222 1800-14-7201 0 800-20 12 90 0 800-74 876 80 88 12 66 0 800-90 90 52 0 800-182 6831 800-90-0474 001-803-1-003-2165 1 800-55 21 22 800-790695 1-800-80-2335 +31-20-316-7222 0 800-732 4283 0800-443988 Norway Poland Spain Sweden Switzerland Singapore Taiwan Thailand Turkey United Kingdom USA/Canada/ Latin America Other European Countries 800-113 91 00 800-311 12 38 900-98 31 24 0 207 90 073 0 800-83 84 11 800-1101-150 +886-2-2514-2237 001-800-11-0032165 00 800-31 92 91 40 0 800-783 5177 1-800-SEAGATE or +1-405-936-1234 + 31-20-316-7222 Standard Microsoft Installation !Partitioning or formatting a drive erases all data on it. Seagate assumes no liability if you erase your data. Drive Partitioning Partitioning divides the drive into sections or partitions that function as separate logical drives (labeled C, D, E, etc. ). Mark the partition as active to make the partition bootable. Drive Formatting !Use the correct drive letters to prevent formatting a drive that already contains data. At the A: prompt, type format x: where x is the letter of your first new partition. Proceed to "Loading the Operating System" below. Warranty To determine the warranty status of your Seagate disc drive, contact your place of purchase or visit our Web site at www. seagate. com for more information. RMA (Return Merchandise Authorization) Run SeaTools to diagnose your drive before requesting a return authorization. In addition, please verify that your drive is defective by following the troubleshooting checklist in this guide. [. . . ] Alle Arbeiten auf dem Festplatte dürfen nur von Ausgebildetem Servicepersonal durchgeführt werden. Der Einbau des Laufwerkes muss den Anforderungen gemäss DIN IEC 950 VDE 0805/05. 90 entspreche. A, Printed in USA, May 2001 Seagate, Seagate Technology and the Seagate logo are registered trademarks of Seagate Technology LLC. SeaShield, SeaShell and U Series 6 are either registered trademarks or trademarks of Seagate Technology LLC. [. . . ]