User manual MAXTOR U SERIES 9 CE

[. . . ] U Series 9 ce ST3160022ACE ST3120025ACE ST380012ACE U Series 9 ce ST3160022ACE ST3120025ACE ST380012ACE ©2003­ 2004, Seagate Technology LLC All rights reserved Publication number: 100271705, Rev. F May 2004 Seagate, Seagate Technology, and the Seagate logo are registered trademarks of Seagate Technology LLC. SeaTools, SeaFONE, SeaBOARD, and SeaTDD are either registered trademarks or trademarks of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners. [. . . ] · Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure. · Always rest the drive on a padded, antistatic surface until you mount it in the computer. · Do not touch the connector pins or the printed circuit board. · Do not remove the factory-installed labels from the drive or cover them with additional labels. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination. U Series 9 ce Product Manual, Rev. F 15 3. 2 Breather filter hole precautions This section contains information regarding the precautions which should be taken regarding the breather filter hole in Seagate hard disc drives. Proper precautions should be taken to ensure full functionality and prevent possible damage to the drive. Breather Hole Do not cover or seal. Figure 1. Breather filter hole location Caution: Do not cover, seal, or insert any object into this hole. This hole has two purposes: · To allow condensation inside the hard disc to escape · To allow air pressure inside the hard disc to equalize with ambient pressure Note. If this hole is covered, sealed, or penetrated by any object, the drive reliability may be compromised and could lead to permanent damage--doing so voids the warranty. 16 U Series 9 ce Product Manual, Rev. F 3. 3 3. 3. 1 Jumper settings Master/slave configuration The options jumper block shown in Figure 1 is used to configure the drive for operation. It is the 8-pin dual header between the interface connector and the power connector. Use the following settings to configure the drive as a master or a slave. The drive is configured at the factory for a master or single-drive operation with a jumper set on pins 7 and 8. Use this jumper setting only if the drive does not work as a master with no jumpers installed. Options jumper block Master or single drive Drive is slave Master with non ATAcompatible slave Cable select Limit drive capacity to 32 Gbytes 7531 8642 Figure 1. Circuit Board Master/slave jumper settings 3. 3. 2 Cable-select option Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. To enable cable select, set a jumper on pins 5 and 6 as shown in Figure 1. Refer to your computer manual to determine whether your computer supports this option. 3. 3. 3 Alternate capacity jumper Some older computers may "hang" at startup if their BIOS detects a disc drive with a capacity greater than 32 Gbytes. This limits the drive's capacity to 32 Gbytes when the alternate capacity jumper is used. To access the full capacity of the drive, you can: · Update the BIOS · Use third-party software such as DiscWizardTM or Disk Manager · Use a third-party host adapter For drives with capacities greater than 32 Gbytes, the alternate capacity jumper changes the total available LBA sectors to 32 Gbytes to solve issues with some BIOS during power on. [. . . ] Have your drive's "ST" model number and serial number available. Authorized Service Centers In some locations outside the US, you can contact an Authorized Service Center for service. 32 U Series 9 ce Product Manual, Rev. F USA/Canada/Latin America Support Services Presales Support Call Center Americas Toll-free 1-877-271-32851 Toll-free 1-800-SEAGATE2 Toll-free 1-800-468-34724 Direct dial +1-405-324-47301 Direct dial +1-405-324-47003 Direct dial +1-405-324-47204 FAX +1-405-324-4704 FAX +1-405-324-4702 FAX / Internet +1-405-324-4722 Technical Support Call Center Americas Warranty Service Call Center USA, Mexico and Latin America Canada Memofix5 Brazil MA Centro de Serviços5 1-800-636-6349 +1-905-660-4936 +1-905-660-4951 www. memofix. com -- +55-21-2509-7267 +55-21-2507-6672 www. mainformatica. com. br/produtos. htm 1Hours 2For of operation are 8:00 A. M. to 6:00 P. M. , Monday through Friday (Central time) product-specific phone number 3Hours of operation are 8:00 A. M. to 8:00 P. M. , Monday through Friday (Central time) 4Hours of operation are 8:30 A. M. [. . . ]