User manual MAXTOR TM1010

[. . . ] Application Note: PULNiX TM-1010 Camera Descriptions · · · · · · Interfacing non-standard cameras to Matrox Pulsar February 10, 1998 996 x 1016 x 10-bit. Continuous mode (analog and digital video output), asynchronous reset mode (pulse width control mode) Interface Modes · Camera Interface Briefs Mode 1: Continuous mode (analog video output) PULNiX TM 1010 Video Matrox Pulsar · · · · · 1000 x 1016 x 10-bit @ 15fps. [. . . ] DCF used: TM1010AE. DCF Mode 1: Continuous mode (analog video output) Cabling Requirements · · · IMG-7W2-TO-1BNC cable required for video output of camera (single channel). Video input BNC of IMG-7W2-TO-1BNC cable should be connected to VIDEO OUT BNC connector of camera. The two switches on the rear of the camera must be set respectively to NRM (normal mode) and NSP (normal speed); the Shutter Control Switch on the rear of the camera must be set to 0 (no shutter). Mode 2: Continuous mode (digital video output) · · PULSAR/DIG/MOD required for digital data and syncs in RS-422 format The two switches on the rear of the camera must be set respectively to NRM (normal mode) and NSP (normal speed); the Shutter Control Switch on the rear of the camera must be set to 0 (no shutter). PUL-CID-045 2 Application Note: PULNiX TM-1010 Interfacing non-standard cameras to Matrox Pulsar February 10, 1998 Cabling Requirements (Continued) · The connections between the 68-pin connector of the PULSAR/DIG/MOD and the 31-pin connector of the camera are as follows: PULSAR/DIG/MOD (68-pin connector) Pin name Pin no. CLKIN+ 29 CLKIN- 63 HSYNC+ 26 HSYNC- 60 VSYNC+ 25 VSYNC- 59 GROUND 34 GROUND 12 DATA0+ 20 DATA0- 54 DATA1+ 19 DATA1- 53 DATA2+ 16 DATA2- 50 DATA3+ 15 DATA3- 49 DATA4+ 14 DATA4- 48 DATA5+ 13 DATA5- 47 DATA6+ 11 DATA6- 45 DATA7+ 10 DATA7- 44 DATA8+ 09 DATA8- 43 DATA9+ 08 DATA9- 42 PULNiX TM-1010 (31-pin DC connector) Pin name Pin no. CLK+ 01 CLK- 17 LDV+ 02 LDV- 18 FDV+ 03 FDV- 19 GND 04 GND 16 D0+ 06 D0- 22 D1+ 07 D1- 23 D2+ 08 D2- 24 D3+ 09 D3- 25 D4+ 10 D4- 26 D5+ 11 D5- 27 D6+ 12 D6- 28 D7+ 13 D7- 29 D8+ 14 D8- 30 D9+ 15 D9- 31 Mode 3: Asynchronous Reset (Pulse Width Control Mode) · · IMG-7W2-TO-5BNC cable required for TTL external trigger; PULSAR/DIG/MOD required for digital data and syncs in RS-422 format, and for TTL control signals. The two switches on the rear of the camera must be set respectively to ASY (asynchronous shutter mode) and NSP (normal speed); the Shutter Control Switch on the rear of the camera must be set to 9 (external pulse width control mode). PUL-CID-045 3 Application Note: PULNiX TM-1010 Cabling Requirements (Continued) · Interfacing non-standard cameras to Matrox Pulsar February 10, 1998 The connections between the 68-pin connector of the PULSAR/DIG/MOD and the 31-pin connector of the camera are as in continuous mode (digital video output) with the exception of the following: PULSAR/DIG/MOD (68-pin connector) Pin name TTL_EXPOSURE1 · Pin no. VINIT 20 TTL external trigger source should be connected to the TTL Trigger Input of the IMG-7W2TO-5BNC cable. An RS-422 external trigger input may also be used once the following connections between the 68-pin connector of the PULSAR/DIG/MOD and the external trigger source are made: PULSAR/DIG/MOD (68-pin connector) Pin name Pin no. TRIGGER+ 27 TRIGGER61 External trigger source Pin name "RS-422 TRIGGER+" "RS-422 TRIGGER-" · · Use Matrox Intellicam in order to modify the DCF for an RS-422 external trigger input. Consult the Matrox Intellicam User Guide for more information The DCF(s) mentioned in this application note can be found on the MIL and MIL-Lite CD, or our FTP site (ftp. matrox. com). [. . . ] SL2 4JS Tel: +44 (0) 1753 665500 Fax: +44 (0) 1753 665599 France Matrox France SARL 2, rue de la Couture, Silic 225 94528 Rungis Cedex Tel: (0) 1 45-60-62-00 Fax: (0) 1 45-60-62-05 Germany Matrox GmbH Inselkammerstr. 8 D-82008 Unterhaching Germany Tel: 089/614 4740 Fax: 089/614 9743 Asia Pacific Matrox Asia Liaison Office Rm. 1901, 19/F, Workington Tower, 78 Bonham Strand E. , Sheung Wan, Hong Kong. [. . . ]