User manual MAXTOR SV35 SERIES SATA REV C 10-2007

[. . . ] Product Manual SV35 Series SATA ST3500641SV ST3250824SV ST3160812SV 100415208 Rev. C October 2007 Revision history Revision Date Sheets affected or comments Rev. 4, 8, 11 and 18. Copyright © 2006-2007 Seagate Technology LLC. C October 2007 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. [. . . ] For installations which require cables, you can connect the drive as illustrated in Figure 5. Signal connector Power connector Signal cable Power cable Figure 5 Attaching SATA cabling Each cable is keyed to ensure correct orientation. SV35 Series SATA drives support latching SATA connectors. SV35 Series SATA Product Manual, Rev. C 25 3. 5 Drive mounting You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. Follow these important mounting precautions when mounting the drive: · Allow a minimum clearance of 0. 030 inches (0. 76 mm) around the entire perimeter of the drive for cooling. · The screws should be inserted no more than 0. 150 inch (3. 81 mm) into the bottom or side mounting holes. · Do not overtighten the mounting screws (maximum torque: 6 inch-lb). Recommended case temperature measurement location [1] 5. 787 (146. 9898) max. 1. 122 + . 020 (28. 499 + . 508) [1] 1. 638 (41. 605) [1] 4. 000 (101. 6) [1] 4. 000 (101. 6) 1. 028 max [1] (26. 111 max) . 814 (20. 676) . 250 + . 015 (6. 35 + . 381) (3x both sides) . 138 (3. 505) C of conn. Datum B L 2. 00 (50. 80) C of drive L Notes: Dimensions are shown in inches (mm). [1] Dimensions per SFF-8301 specification [1] 2 x 3. 750 (2 x 95. 25) 2 x 1. 625 (2 x 41. 28) [1] 2 x 1. 750 [1] (2 x 44. 45) 4. 000 (101. 6) [1] Recommended case temperature measurement location Figure 6 Mounting dimensions--top, side and end view 26 SV35 Series SATA Product Manual, Rev. C 4. 0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0­4; multiword DMA modes 0­2, and Ultra DMA modes 0­6. For detailed information about the Serial ATA interface, refer to the "Serial ATA: High Speed Serialized AT Attachment" specification. 4. 1 Hot-Plug compatibility SV35 Series SATA drives incorporate connectors which enable you to hot plug these drives in accordance with the Serial ATA II: Extension to Serial ATA 1. 0a specification. This specification can be downloaded from www. serialata. org. SV35 Series SATA Product Manual, Rev. C 27 4. 2 Serial ATA device plug connector pin definitions Table 6 summarizes the signals on the Serial ATA interface and power connectors. . Table 6: Segment Serial ATA connector pin definitions Pin S1 S2 S3 S4 S5 S6 Function Ground A+ AGround BB+ Ground 2nd mate Key and spacing separate signal and power segments P1 P2 P3 P4 P5 P6 P7 V33 V33 V33 Ground Ground Ground V5 V5 V5 Ground Ground or LED signal Ground V12 V12 V12 3. 3V power 3. 3V power 3. 3V power, pre-charge, 2nd mate 1st mate 2nd mate 2nd mate 5V power, pre-charge, 2nd mate 5V power 5V power 2nd mate If grounded, drive does not use deferred spin 1st mate. 12V power, pre-charge, 2nd mate 12V power 12V power 2nd mate Differential signal pair B from Phy Definition 2nd mate Differential signal pair A from Phy Signal S7 Power P8 P9 P10 P11 P12 P13 P14 P15 Notes: 1. The comments on the mating sequence apply to the case of backplane blindmate connector only. C case, the mating sequences are: · the ground pins P4 and P12. One pin from each voltage is used for pre-charge when installed in a blind-mate backplane configuration. All used voltage pins (Vx) must be terminated. SV35 Series SATA Product Manual, Rev. C 29 4. 3 Supported ATA commands The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification. commands" on page 38. for details and subcommands used in the S. M. A. R. T. [. . . ] Worldwide support is available 24 hours daily by email for your questions. Presales Support: Presales@Seagate. com Technical Support: DiscSupport@Seagate. com Warranty Support: http://www. seagate. com/support/service/index. html mySeagate my. seagate. com is the industry's first Web portal designed specifically for OEMs and distributors. It provides self-service access to critical applications, personalized content and the tools that allow our partners to manage their Seagate account functions. Submit pricing requests, orders and returns through a single, password-protected Web interface-anytime, anywhere in the world. [. . . ]