User manual MAXTOR ST9190AG

[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST9190 Family: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST9190 Family: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ©1994 Seagate Technology, Inc. B July 1994 Seagate®, Seagate Technology® and the Seagate logo are registered trademarks of Seagate Technology, Inc. [. . . ] B This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television, which can be determined by turning the equipment on and off, you are encouraged to try one or more of the following corrective measures: · Reorient the receiving antenna. · Plug the computer into a different outlet so that the receiver and computer are on different branch outlets. If necessary you should consult your dealer or an experienced radio/television technician for additional suggestions. You may find helpful the following booklet prepared by the Federal Communications Commission: How to Identify and Resolve Radio-Television Interference Problems. Refer to publication number 004-000-00345-4. ST9190 Family Product Manual, Rev. B 11 2. 0 Drive mounting and configuration 2. 1 Handling and static-discharge precautions After unpacking, and prior to installation, the drive may be exposed to potential handling and ESD hazards. Avoid contact with the printed circuit board, all electronic components and the interface connector. Always rest the drive on a padded antistatic surface until you mount it in the host system. 2. 2 Mounting the ST9190 family drives You can mount ST9190 family drives in any orientation. Allow a minimum clearance of 0. 030 inches (0. 76 mm) around the entire perimeter of the drive for cooling. Figure 2 on page 12 provides mounting dimensions for the ST9190 family drives. These drives conform to the industry-standard MCC directmounting specifications and require the use of MCC-compatible connectors in direct-mounting applications. The I/O connector pins may extend up to 0. 010 inches beyond the edge of the head/disc assembly. To avoid damaging the drive: · Use M3X0. 5 metric mounting screws only. · Do not insert mounting screws more than 0. 150 inches (3. 81 mm) into the mounting holes. · Do not overtighten the screws (maximum torque: 3 inch-lb). 12 ST9190 Family Product Manual, Rev. B Dimensions are in inches (mm) 0. 489 ± 0. 015 (12. 42 ± 0. 38) 4. 010 (101. 85) max. (head/disc assembly) 0. 118 ± 0. 010 (3. 00 ± 0. 25) 0. 000 in (mm) 4X 3 mm × 0. 5 mm, 0. 15 in (3. 81mm) min. full thread 0. 152 ± 0. 005 (3. 86 ± 0. 13) 1. 227 ± 0. 020 (31. 17 ± 0. 51) 4. 020 (102. 11) max. (head/disc assembly to tip of pins) 1. 500 ± 0. 010 (38. 10 ± 0. 25) 0. 000 1. 375 ± 0. 015 (34. 93 ± 0. 38) 0. 155 ± 0. 020 (3. 94 ± 0. 51) 0. 000 0. 239 ± 0. 035 (6. 07 ± 0. 89) 2. 740 ± 0. 020 (69. 60 ± 0. 51) 2. 430 ± 0. 010 (61. 72 ± 0. 25) 4X 3 mm × 0. 5 mm, 0. 15 in (3. 81 mm) min. full thread Pin 1 0. 079 (2. 00) 0. 157 ± 0. 010 (3. 99 ± 0. 25) 0. 079 (2. 00) Pin 20 removed for keying Figure 2. [. . . ] The ATA interface cable should be no more than 18 inches long. Dimensions are in inches (mm) Master/slave jumpers 0. 079 ± 0. 003 (2. 00 ± 0. 08) 0. 020 ± 0. 002 (0. 51 ± 0. 05) 0. 152 ± 0. 005 (3. 71 ± 0. 20) 0. 020 ± 0. 002 (0. 51 ± 0. 05) 1. 654 (42. 01) 0. 079 ± 0. 003 (2. 00 ± 0. 08) 0. 158 ± 0. 003 (4. 00 ± 0. 08) Figure 4. The I/O connector pins may extend up to 0. 010 inches beyond the edge of the head/disc assembly. 18 ST9190 Family Product Manual, Rev. B 3. 2 ATA interface signals and connector pins The following diagram summarizes the signals on the ATA interface connector that are supported by the ST9190 family drives. For a detailed description of these signals, refer to the Seagate ATA Interface Reference Manual. Drive pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Signal name Reset­ Ground DD7 DD8 DD6 DD9 DD5 DD10 DD4 DD11 DD3 DD12 DD2 DD13 DD1 DD14 DD0 DD15 Ground (removed) Reserved Ground DIOW­ Ground DIOR­ Ground Reserved CSEL Reserved Ground INTRQ IOCS16­ DA1 PDIAG­ DA0 DA2 CS1FX­ CS3FX­ DASP­ Ground Power Power Ground Reserved Host pin # and signal description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Host Reset Ground Host Data Bus Bit 7 Host Data Bus Bit 8 Host Data Bus Bit 6 Host Data Bus Bit 9 Host Data Bus Bit 5 Host Data Bus Bit 10 Host Data Bus Bit 4 Host Data Bus Bit 11 Host Data Bus Bit 3 Host Data Bus Bit 12 Host Data Bus Bit 2 Host Data Bus Bit 13 Host Data Bus Bit 1 Host Data Bus Bit 14 Host Data Bus Bit 0 Host Data Bus Bit 15 Ground (No Pin) Reserved Ground Host I/O Write Ground Host I/O Read Ground Reserved Cable Select Reserved Ground Host Interrupt Request Host 16 Bit I/O Host Address Bus Bit 1 Passed Diagnostics Host Address Bus Bit 0 Host Address Bus Bit 2 Host Chip Select 0 Host Chip Select 1 Drive Active/Slave Present Ground +5 volts DC (logic) +5 volts DC (motor) Ground for power pins Reserved Pins 28, 34 and 39 are used for master-slave communication (details shown below). [. . . ]