User manual MAXTOR ST5252160A INSTALLATION

[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist Pro 2160sl (ST52160A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist Pro 2520sl (ST52520A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . for ATA (IDE)-Compatible PCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -2 Medalist Pro 2160sl and 2520sl, Rev. B, May 1999 Seagate, Seagate Technology and the Seagate logo are registered trademarks of Seagate Technology, Inc. [. . . ] Do not install a jumper on these pins. Medalist Pro 2160sl and 2520sl, Rev. B 19 Cable select jumper Some computers differentiate between master and slave drives using specially designed interface cables that have the line to pin 28 (the Cable Select pin) removed or cut at one connector. See your computer manual to determine whether your computer supports this feature. To configure your Seagate drive for cable select, place a jumper on pins 5 and 6 and pins 7 and 8, as shown in Figure 5. 20 Medalist Pro 2160sl and 2520sl, Rev. B Advanced Disk Manager options The Disk Manger online manual Disk Manager contains an extensive online manual. This manual includes detailed installation instructions, troubleshooting and a list of master/slave jumper settings for many popular hard drives. To view the Disk Manager online manual, insert the Disk Manager diskette into drive A and type A:\DM /H. You can also view the online manual from within Disk Manager by selecting (V)iew/Print Online Manual in the main menu. Booting from a diskette If Disk Manager installs the dynamic drive overlay (DDO) to access the full capacity of your drive, the DDO must load into memory before the operating system loads. This occurs automatically when you boot from your hard drive (drive C). However, if you boot from a diskette, the DDO will not be loaded and you will not be able to access your hard drive. The following procedure allows you to boot from a diskette and still access your hard drive. Boot the computer from the hard disc (with no diskette in the diskette drive). When the Disk Manager banner appears on the screen, immediately press the SPACEBAR (you have about 2 seconds). If you boot from a diskette regularly, you can create a Dynamic Drive Overlay boot diskette. See the Disk Manager online manual for more information about creating a dynamic drive overlay boot diskette. Medalist Pro 2160sl and 2520sl, Rev. B 21 Supported operating systems The Disk Manager dynamic drive overlay provides support for drives with capacities greater than 528 Mbytes under MS-DOS, Windows 3. x, Windows 95, Windows NT 3. 51, Windows NT 3. 50 (requires DM upgrade drivers), OS/2 V3. 0 (Warp full pack), and OS/2 V2. 0­3. 0 (requires DM upgrade drivers). Before you install a non-DOS operating system on the drive, install DOS and Disk Manager and make sure that the drive is bootable. Instructions for running the dynamic drive overlay with other operating systems are available in the Disk Manager online manual. Removing the dynamic drive overlay If Disk Manager installs a dynamic drive overlay (DDO) and you do not need this software to access the full capacity of your drive, you can remove the dynamic drive overlay without losing your data. However, you will lose access to the full capacity of your drive unless you have another method for accessing highcapacity drives (see "Addressing drive-capacity limitations" on page 11). ! Caution. Before you attempt to remove a DDO, make a backup copy of all the data on your hard drive. Also, run CHKDSK, SCANDISK or a third-party equivalent to detect and repair any damaged files before you follow the procedure below. If the DDO migration program encounters a serious file problem or is interrupted by a power loss or hardware failure, the migration will fail and your data will be lost. 22 Medalist Pro 2160sl and 2520sl, Rev. [. . . ] B Warranty Repair USA Mexico and Latin America 1-800-468-3472 +1-405-949-7758 FAX: +1-405-949-6740 FAX: +1-405-949-6738 Brazil MA Informatica* +55-21-516-6649 Canada Memofix* Adtech* +1-905-660-4936 +1-905-812-8099 or 1-800-624-9857 FAX: +55-21-516-5280 FAX: +1-905-660-4951 FAX: +1-905-812-7807 *Authorized service center European Support Services For European customer support, dial the toll-free number for your specific country for presales support, technical support, SeaFAX and warranty repair. If your country is not listed here, dial our European call center at +31-20-316-7222 from 8:30 A. M. The European call center is located in Amsterdam, The Netherlands. Call Center Austria Belgium Denmark France Germany Ireland Italy 0 800-20 12 90 0 800-74 876 80 88 12 66 0 800-90 90 52 0 800-182 6831 1 800-55 21 22 1 677 90 695 Medalist Pro 2160sl and 2520sl, Rev. B Netherlands Norway Poland Spain Sweden Switzerland Turkey United Kingdom 0 800-732 4283 800-113 91 00 800-311 12 38 900-98 31 24 0 207 90 073 0 800-83 84 11 00 800-31 92 91 40 0 800-783 5177 +49-89-1409331 35 SeaBOARD Germany Fax Services--All European Countries Presales/Technical Support/Warranty Repair +31-20-653-3513 Africa/Middle East Support Services For presales, technical support, warranty repair and FAX services in Africa and the Middle East, dial our European call center at +31-20-316-7222 from 8:30 A. M. [. . . ]