User manual MAXTOR ST52160A

[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist Pro Family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist Family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . © 1997 Seagate Technology, Inc. C, February 1997 Seagate, Seagate Technology and the Seagate logo are registered trademarks of Seagate Technology, Inc. [. . . ] If this equipment does cause interference to radio or television, which can be determined by turning the equipment on and off, you are encouraged to try one or more of the following corrective measures: · Reorient the receiving antenna. · Plug the equipment into a different outlet so that the receiver and computer are on different branch outlets. If necessary, you should consult your dealer or an experienced radio/television technician for additional suggestions. You may find helpful the following booklet prepared by the Federal Communications Commission: How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Superintendent of Documents, US Government Printing Office, Washington, DC 20402. This digital apparatus does not exceed the Class B limits for radio noise emissions from computer equipment as set out in the radio interference regulations of the Canadian Department of communications. Le présent appareil numérique német pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par le Ministère des Communications du Canada. 16 Medalist Pro 2520/2160 Product Manual, Rev. Das Gerrät ist ein Einbaugerät, das für eine maximale Umgebungstemperatur von 55°C vorgesehen ist. Zur Befestigung des Laufwerks werden 4 Schrauben 6-32 UNC-2A benötigt. Bei seitlicher Befestigung darf die maximale Länge der Schrauben im Chassis nicht mehr als 5, 08 mm und bei Befestigung an der Unterseite nicht mehr als 5, 08 mm betragen. Als Versorgungsspannugen werden benötigt: +5V æ 5% 0. 55A +12Væ 5% 0. 35A (1, 9A fur ca. Alle Arbeiten an der Festplatte dürfen nur von ausgebildetem Servicepersonal durchgeführt werden. Der Einbau des Laufwerkes muss den Anforderungen gemäss DIN IEC 950 V DE 0805/05. 90 entsprechen. Medalist Pro 2520/2160 Product Manual, Rev. C 17 2. 0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 2. 1 Handling and static-discharge precautions After you unpack the drive, and before you install it in a system, be careful not to damage it through mishandling. Observe the following standard handling and static-discharge precautions: Caution: · Keep the drive in its static-shielded bag until you are ready to complete the installation. Do not attach any cables to the drive while it is in its static-shielded bag. · Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure. · Always rest the drive on a padded, antistatic surface until you mount it in the computer. · Do not touch the connector pins or the printed circuit board. · Do not remove the factory-installed labels from the drive or cover them with additional labels. Some factory-installed labels contain information needed to service the drive. [. . . ] This changes word 63 of the Identify Drive command to the mode you enter in the Sector Count register. The following table identifies allowable transfer types values: Data-Transfer Mechanism Mechanism name PIO Transfer Mode (default) PIO Transfer Mode: Set PIO Mode = 2 PIO Flow Control Transfer Mode: Set PIO Mode = 0 PIO Flow Control Transfer Mode: Set PIO Mode = 1 PIO Flow Control Transfer Mode: Set PIO Mode = 2 PIO Flow Control Transfer Mode: Set PIO Mode = 3 PIO Flow Control Transfer Mode: Set PIO Mode = 4) Multiword DMA Mode Multiword DMA Mode Multiword DMA Mode Reserved Mode value 2 2 0 1 2 3 4 0 1 2 -- Transfer Types value Data Lower 3 bits Upper 5 bits 00000 00000 00001 00001 00001 00001 00001 00100 00100 00100 01000 000 001 000 001 010 011 100 000 001 010 nnn Note. If the drive does not support a commanded mode, it returns a 04 aborted command error. 34 Medalist Pro 2520/2160 Product Manual, Rev. C 3. 2. 3 Standby timer timeout period The Idle command and Standby command Sector Count registers are used to activate the Standby timer. [. . . ]