User manual MAXTOR ST51080A

[. . . ] INSTALLING YOUR NEW SEAGATE HARD DRIVE HANDLE WITH CARE! Disc drives are extremely fragile. Do not drop or jar your drive. WHAT YOU WILL NEED MEDALIST SL HARD DRIVE INSTALLATION GUIDE Medalist 540sl (ST5540A) Medalist 851sl (ST5851A) Medalist 1080sl (ST51080A) Medalist 1270sl (ST51270A) for ATA (IDE)-Compatible PCs Thank you for selecting a Seagate disc drive. Installing your new Seagate hard drive is easy when you use this easy drive-installation sheet. For technical information and troubleshooting tips, see the back of this sheet. [. . . ] Another solution is to warm-boot your computer after every power-on. Note. If your are installing OS/2 or Windows NT, we suggest that you print the instructions before you start the installation. To use DDO with OS/2 and Windows NT V3. 5, you must replace up to four of the original files with files supplied by Disk Manager. The replacement files are located in the OS2 and the NT subdirectories on your Seagate software diskette. The online manual tells you which files you need to replace and under what conditions to replace them. If you need assistance renaming a file, refer to your DOS reference manual. If you need to make a copy of an installation diskette, follow the instructions below--the installation diskette will not install if you use the standard copy command to copy it. 1 Insert the original diskette into Drive A and access the drive. · Check for I/O address conflicts. To isolate the conflict, verify that the drive and host adapter are compatible with your computer by removing all the peripheral adapter cards (power must be off) except for the video card. If this is successful, reinstall the other peripherals one at a time until the conflict occurs. After you have isolated the source of the address conflict, you can resolve the conflict by changing the I/O address of the peripheral that appears to cause the conflict. SeaFAX You can use a touch-tone telephone to access Seagate's automated FAX system to receive technical support information by return FAX. Location United States England Telephone number 408-438-2620 44-1-62-847-7080 ADDITIONAL INSTALLATION OPTIONS This section provides a brief discussion of the options on the options jumper block. 2 Type diskcopy a: a: . The computer will read the original diskette and prompt you to insert the destination diskette into Drive A. Erase the files you need to replace on the copy diskette, and copy the replacement files using the standard copy command. (If only one diskette drive is available for copying, first copy the required files to the hard drive from the appropriate subdirectory. Then copy the files to your new diskette. ) · If you are booting from a diskette and Disk Manager installed your drive using DDO, the drive information in the boot record was not loaded. If you want to boot with the diskette, follow the "Booting with a Diskette" instructions in column one. Single Drive or Master with an ATA-Compatible Slave This is the factory default setting. The jumpers are on pins 2 and 4 and on pins 5 and 6. The dealer partitioned and formatted the drive for you in the store, but the drive does not respond when you install it. · Slave To make the drive the slave, move the jumper on pins 2 and 4 to pins 1 and 2. Removing the Dynamic Drive Overlay If Disk Manager installs your drive with DDO, you can, in many cases, remove DDO without losing your data. However, you will lose access to the full capacity of your drive unless you use another method that supports more than 528 Mbytes (see "Accessing More Than 528 Mbytes" on the front side). Three steps are required to remove DDO safely: 1) migrating the data, 2) configuring Setup with the drive's translation and 3) uninstalling the DDO. Follow the instructions below to safely remove the DDO. Reboot the computer and make sure the drive spins up. Check all cables. This symbol provides the SeaFAX document number for the product or products being discussed where it appears. · Make sure the power supply is adequate for system needs. [. . . ] Bei seitlicher Befestigung darf die maximale Länge der Schrauben im Chassis nicht mehr als 3, 3 mm und bei Befestigung an der Unterseite nicht mehr als 5, 08 mm betragen. Als Versorgungsspannugen werden benötigt: +5V ± 5% 0, 6A; +12V ±% 0, 8A (1, 9A fur ca. Alle Arbeiten auf dem Festplatte dürfen nur von Ausgebildetem Servicepersonal durchgeführt werden. Der Einbaudes Drives muss den Anforderungen gemäss DIN IEC 950V DC 0805/05. 90 entsprechen. [. . . ]