User manual MAXTOR ST446452W INSTALLATION
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAXTOR ST446452W. We hope that this MAXTOR ST446452W user guide will be useful to you.
You may also download the following manuals related to this product:
MAXTOR ST446452W VOLUME 1 (1244 ko)
Manual abstract: user guide MAXTOR ST446452WINSTALLATION
Detailed instructions for use are in the User's Guide.
[. . . ] ··
·
··
·
·
··
·
·
··
·
·
··
·
··
·
·
··
·
·
Elite 47
·· · ·· · · ·· · · ·· · · ·· · ·· · · ·· · ·
Disc Drive
·· · ·· · · ·· · · ·· · · ·· · ·· · · ·· · ·
ST446452W
·· · ·· · · ·· · · ·· · · ·· · ·· · · ·· · ·
··
·
··
·
·
··
·
·
··
·
·
··
·
··
·
·
··
·
·
Installation Guide
·· · ·· · · ·· · · ·· · · ·· · ·· · · ·· · ·
Contents
Preface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Electrostatic discharge protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Important safety information and precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Wichtige Sicherheitshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory agency compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Technical support services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 General description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Initial setup information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 10% tolerance is permissible during initial start of the spindle but must return to ±5% before reaching 5, 357 r/min. The ±5% must be maintained after the drive signifies that its power-up sequence has been completed and that the drive is able to accept selection by the host initiator. the +12V current profile in the Elite 47 Product Manual (publication number 83329280). condition occurs when the Motor Start option is enabled and the drive has not yet received a Start Motor command.
2A
3 See
4 This
5 See
"Conducted noise immunity" in the Elite 47 Product Manual. The specified voltage tolerance is inclusive of ripple, noise, and transient response. power-up, the motor current regulator limits the +12V current to an average value of less than 4. 8A, although instanta-
6 At
Elite 47 Installation Guide, Rev. These peaks should measure 5 msec duration or less.
7 Minimum
current loading for each supply voltage is not less than 4% of the maximum operating current shown. separate ground returns for +5V and +12V supplies.
8 Use
9 Where
power is provided to multiple drives from a common supply, carefully consider individual-drive power requirements. Where multiple units are powered on simultaneously, be sure the peak starting current is available to each device.
10 No
terminator power. Dimensions of the drive
Typical inches mm Maximum inches mm
Table 3:
Height Width Depth
3. 25 5. 75 8. 0
82. 6 146. 1 203. 0
3. 268 5. 76 8. 01
83. 0 146. 3 203. 5
Weight 7. 0 pounds (3. 18 kilograms)
18
Elite 47 Installation Guide, Rev. B
Initial setup information
The following topics are discussed in this section: · · · · · · · · SCSI ID jumpers Drive termination Terminator power Interface drivers and data path width notes Other applicable jumper options Providing adequate cooling Mounting the drive and connecting cables Formatting the drive
Elite 47 Installation Guide, Rev. B
19
SCSI ID jumpers
Each device on the SCSI chain must have a unique SCSI ID. The host system's SCSI controller usually uses the ID that has the highest priority interrupt in the SCSI I/O system. The lower priority SCSI IDs are normally used for other SCSI devices such as this Elite disc drive. Other controllers do not allow this so be sure to refer to your system or controller user's manual for details about its requirements for proper SCSI device installation. This drive is a SCAM (SCSI Configured Auto Magically) compliant drive. If the system into which you are installing this drive requires SCAM compliant drives, you do not need to be concerned about the drive ID jumper settings, as the system automatically assigns your new drive the ID it wants it to have. Setting the drive ID doesn't hurt anything, but is not necessary in a SCAM compliant system.
20
Elite 47 Installation Guide, Rev. B
Most Elite 47 disc drives are factory set with the SCSI ID set at 0. To change the SCSI ID, install jumpers on the appropriate pins as shown in Figure 2.
J4A Pin 1 SCSI ID = 0 (default) SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7 SCSI ID = 8* SCSI ID = 9* SCSI ID = Ah (10)* SCSI ID = Bh (11)* SCSI ID = Ch (12)* SCSI ID = Dh (13)* SCSI ID = Eh (14)* SCSI ID = Fh (15)* Pin 15 Pin 1 J4A J01 J6 SCSI I/O Connector DC Power Connector J4B
Pin 1
Figure 2.
Setting the SCSI ID
If, after completing the installation process, the drive's LED does not show on/off activity when the host is trying to communicate with the drive, a duplicate SCSI ID may be the problem. If this is the case, change the ID so that each device on the SCSI chain has its own unique ID. Also check your system or controller
Elite 47 Installation Guide, Rev. [. . . ] DC power connector Abbildung 11. Gleichstromanschluß
36
Elite 47 Installation Guide, Rev. Signal ground on the printed circuit board assembly (PCBA) and the head and disc assembly (HDA) are connected together in this drive and you cannot separate them. Ensure the equipment in which you have mounted the drive is connected directly to the HDA. Maximizing the conductive contact area between HDA ground and system ground may reduce radiated emissions. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE MAXTOR ST446452W
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAXTOR ST446452W will begin.