User manual MAXTOR ST34520 VOLUME 1

[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist Pro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST39140N/W/WC/LW/LC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST36530N/W/WC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST34520N/W/WC/LW/LC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Manual, Volume 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist Pro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST39140N/W/WC/LW/LC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST36530N/W/WC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST34520N/W/WC/LW/LC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Manual, Volume 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . © 1997-1999 Seagate Technology, Inc. D February 1999 Seagate, Seagate Technology, and the Seagate logo are registered trademarks of Seagate Technology, Inc. [. . . ] Appendix A of this manual lists the sense keys and additional sense codes supported by the drives of this manual. The Receive Diagnostic Results reports the results of diagnostic operations performed by the drive. Status returned by the drive to the Initiator is described in the SCSI Interface Product Manual. Status reporting plays a role in the SCSI systems error management and its use in that respect is described in sections where the various commands are discussed. Medalist Pro Product Manual, Rev. D 33 8. 0 Installation The first thing to do when installing a drive is to set the drive ID (select) on the SCSI bus and set up certain operating options. This is usually done by installing small shorting jumpers on the pins of connector J2 on the PCB (or J1-Auxiliary on the "W" and "LW" models), or via the drive to host I/O signals on "WC" and "LC" models. Some users connect cables to J6 or J1-Auxiliary and perform the set-up using remote switches. If your system is "SCAM" (SCSI Configured Auto Magically) compliant, the system assigns the drive ID over the interface, so there is no need to be concerned about drive ID. Setting the drive ID jumpers doesn't hurt anything, but is not necessary. If your system is not "SCAM" compliant you need to set the drive ID using the ID jumpers. Configure drive options For option jumper locations and definitions refer to Figures 9, 10, 11, 12, 13, and 14. Drive default mode parameters are not normally needed for installation. Refer to Section 9. 3. 2 for default mode parameters if they are needed. · Ensure that the SCSI ID of the drive is not the same as the host adapter. · If multiple devices are on the bus set the drive SCSI ID to one that is not presently used by other devices on the bus. · If the drive is the only device on the bus, attach it to the end of the SCSI bus cable. Permanently installed terminators must be enabled on the drive for "N" and "W" models using jumper plug TE if termination is not provided by the host equipment. On "WC, " "LC, " and "LW" models, external terminators must be provided by the user, systems integrator or host equipment manufacturer. · If the drive is attached to a bus that contains other devices, and the new drive is not attached to the end of the bus, the Terminator Enable jumper (TE) should be removed from the new drive. For additional information about terminator requirements, refer to Sections 9. 8 and 9. 9. · Set all appropriate option jumpers for desired operation prior to power on. If jumpers are changed after power has been applied, recycle the drive power to make the new settings effective. [. . . ] You can send questions or comments 24 hours daily and exchange messages with a technical support specialist from 8:00 A. M. (central time) Monday through Friday. Customer Service (CSO) Warranty Repair Seagate offers worldwide customer support for Seagate drives. Seagate direct OEM, Distribution and System Integrator customers should contact their Seagate service center representative for warranty information. Other customers should contact their place of purchase. Authorized Service Centers If your live outside the U. S. , you can contact an Authorized Service Center for service or repair. 78 Medalist Pro Product Manual, Rev. [. . . ]