User manual MAXTOR ST136403LC VOLUME 1

[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cheetah 36 Family: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST136403LW/LC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Manual, Volume 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cheetah 36 Family: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST136403LW/LC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Manual, Volume 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . © 1999 Seagate Technology, Inc. B August 1999 Seagate, Seagate Technology, and the Seagate logo are registered trademarks of Seagate Technology, Inc. [. . . ] The drive shall not incur physical damage or degraded performance as a result of continuous vibration not exceeding 5-22 Hz @ 0. 040 inches (1. 02 mm) displacement 22-400 Hz @ 2. 00 G Vibration may be applied in the X, Y, or Z axis. 6. 4. 5 Air cleanliness The drive is designed to operate in a typical office environment with minimal environmental control. 6. 4. 6 Acoustics Sound power during idle mode shall be 4. 7 bels typical when measured to ISO 7779 specification. There will not be any discrete tones more than 10 dB above the masking noise on typical drives when measured according to Seagate specification 30553-001. There will not be any tones more than 24 dB above the masking noise on any drive. 6. 4. 7 Electromagnetic susceptibility See Section 2. 1. 2. 28 6. 5 Mechanical specifications Cheetah 36 Product Manual, Rev. B The following nominal dimensions are exclusive of the decorative front panel accessory. Refer to Figures 10 and 11 for detailed mounting configuration dimensions. See Section 8. 4, "Drive mounting. " Height: Width: Depth: Weight: 1. 6 in 4. 000 in 5. 75 in 2. 0 pounds 40. 64 mm 101. 6 mm 146. 05 mm 0. 907 kilograms K // T -Z- S [1] H L J B R A -ZM U -XNotes: [1] Mounting holes are 6-32 UNC 2B, three on each side and four on the bottom. Max screw tightening torque is 6. 0 in-lb (3. 32 nm) with minimum full thread engagement of 0. 12 in. -Z- P G [1] A B C D E F G H J K L M P R S T U C -X- F Dimension Table Millimeters Inches 42. 01 max 1. 654 max 147. 00 max 5. 787 max 101. 60 ± . 25 4. 000 ± . 010 92. 25 ± . 25 3. 750 ± . 010 3. 18 ± . 25 . 125 ± . 010 44. 45 ± . 25 1. 750 ± . 010 41. 28 ± . 50 1. 625 ± . 020 28. 50 ± . 50 1. 122 ± . 020 101. 60 ± . 25 4. 000 ± . 010 6. 35 ± . 25 . 250 ± . 010 41. 60 ± . 25 1. 638 ± . 010 4. 60 ± . 50 . 181 ± . 020 1. 625 . 265 . 315 . 015 . 015 ± . 020 ± . 010 ± . 040 max max 41. 28 6. 73 7. 00 0. 38 0. 38 ± . 50 ± . 25 ± . 10 max max E D Figure 10. ST136403LW mounting configuration dimensions Cheetah 36 Product Manual, Rev. B 29 K // T -Z- S [1] H L J B R N -Z- -XNotes: [1] Mounting holes are 6-32 UNC 2B, three on each side and four on the bottom. Max screw tightening torque is 6. 0 in-lb (3. 32 nm) with minimum full thread engagement of 0. 12 in. -Z- A -ZM U -X- P G [1] F A B C D E F G H J K L M N P R S T U D C -X- Dimension Table Inches Millimeters 42. 01 max 1. 654 max 147. 00 max 5. 787 max 101. 60 ± . 25 4. 000 ± . 010 92. 25 ± . 25 3. 750 ± . 010 3. 18 ± . 25 . 125 ± . 010 44. 45 ± . 25 1. 750 ± . 010 41. 28 ± . 50 1. 625 ± . 020 28. 50 ± . 50 1. 122 ± . 020 101. 60 ± . 25 4. 000 ± . 010 6. 35 ± . 25 . 250 ± . 010 41. 61 ± . 25 1. 638 ± . 010 4. 60 ± . 50 . 181 ± . 020 1. 20 max . 040 max 41. 28 ± . 50 1. 625 ± . 020 66. 50 ± . 25 2. 618 ± . 010 7. 00 ± 1. 02 . 276 ± . 040 0. 38 max . 015 max 0. 38 max . 015 max E Figure 11. ST136403LC mounting configuration dimensions Cheetah 36 Product Manual, Rev. B 31 7. 0 Defect and error management The drive, as delivered, complies with this specification. The read error rate and specified storage capacity are not dependent upon use of defect management routines by the host (initiator). Defect and error management in the SCSI system involves the drive internal defect/error management and SCSI systems error considerations (errors in communications between Initiator and the drive). Tools for use in designing a defect/error management plan are briefly outlined in this section, with references to other sections where further details are given. 7. 1 Drive internal defects During the initial drive format operation at the factory, media defects are identified, tagged as being unusable, and their locations recorded on the drive primary defects list (referred to as the "P" list and also as the ETF defect list). At factory format time, these known defects are also reallocated, that is, reassigned to a new place on the medium and the location listed in the defects reallocation table. Locations of defects found and reallocated during error recovery procedures after drive shipment are listed in the "G" list (defects growth list). The "P" and "G" lists may be referenced by the initiator using the Read Defect Data command (see Section 5. 2. 1. 2 in the SCSI Interface Product Manual, part number 77738479). [. . . ] This service is available worldwide. Presales Support Our Presales Support staff can help you determine which Seagate products are best suited for your specific application or computer system. Seagate Express You can purchase select tape products and tape accessories through Seagate Express 24 hours daily by calling 1-800-531-0968 or by faxing your order to: +1-972-481-4812. Technical Support If you need help installing your drive, consult your dealer. Dealers are familiar with their unique system configurations and can help you with system conflicts and other technical issues. If you need additional help, you can talk to a Seagate technical support specialist. Before calling, note your system configuration and drive model number (ST####). SeaTDDTM(+1-405-936-1687) is a telecommunications device for the deaf (TDD). [. . . ]