User manual MAXTOR SMD4M15

[. . . ] Application Note: SMD 4M15 Camera Descriptions · · · · · · Interfacing non-standard cameras to Matrox Genesis February 16, 1998 2048 x 2048 x 12-bit @ 15 fps. This camera outputs 12-bit however only 8-bit was used for this interface Interface mode Camera Interface Briefs · Continuous (no Binning, 2x2 Binning, 4x4 Binning, AOI) Mode 1: Continuous (no Binning) Video SMD 4M15 HSYNC VSYNC Pixel Clock Matrox Genesis (GEN/_/_/STD* + GEN/DIG/BRD/S**) · · · · · · · · 2048 x 2048 x 8-bit @ 15 fps. [. . . ] * Matrox Genesis Main Board with Grab Module 4-channel digital video output (RS-422). Pixel clock frequency: 5 MHz Matrox Genesis receiving RS-422 HSYNC, VSYNC and pixel clock signals from camera. DCF used : SMDC4X4. DCF Note: requires two additional programs for operation (see Camera Interface Details) Mode 4: Continuous (AOI -Area Of Interest) Video SMD 4M15 HSYNC VSYNC Pixel Clock Matrox Genesis (GEN/_/_/STD* + GEN/DIG/BRD/S**) · · · · · · · · * Matrox Genesis Main Board 1024 x 256 x 8-bit @ 15 fps. Pixel clock frequency: 10 MHz Matrox Genesis receiving RS-422 HSYNC, VSYNC and pixel clock signals from camera. DCF used : SMDCAOI. DCF Note: requires two additional programs for operation (see Camera Interface Details) Camera Interface Details Modes 1-4: Data connections and image viewed from front Camera Rear A B POWER DATA 1 DATA 2 DATA 1 DATA 2 GEN-CID-031 2 Application Note: SMD 4M15 Interfacing non-standard cameras to Matrox Genesis February 16, 1998 Camera Interface Details (continued) Modes 1-4: Continuous (no Binning, 2x2 Binning, 4x4 Binning, AOI) · · · In addition to the corresponding DCF file, two supplementary programs are required to operate the camera with the Matrox Genesis: comserial. c (to write data to the PC serial port) and grabsmd. c (to control the Matrox Genesis grabbing). Programming the serial port requires the following usage: "comserial -x addr data" (hexadecimal values) or "comserial -d addr data" (decimal values) Operating Modes: Address 0x81 of the camera controls the principle operating modes. No Binning : comserial -x 81 02 2x2 Binning: comserial -x 81 06 4x4 Binning: comserial -x 81 0a AOI mode : comserial -x 81 42 Mode 4: Continuous (AOI -Area Of Interest) · Start/End registers Addresses 0x89 and 0x8a control the START readout register. The commands below indicate that the readout will start at line 0x30f (783) and end at 0x410 (1040) for a total of 256 lines read out (per tap). comserial -x 8a 0f comserial -x 89 03 comserial -x 8c 10 comserial -x 8b 04 · For more information and options refer to the readme. txt file included with the DCFs and demo program or contact Matrox Imaging Applications at 514-822-6061 for assistance. GEN-CID-031 3 Application Note: SMD 4M15 Interfacing non-standard cameras to Matrox Genesis February 16, 1998 Cabling Requirements Modes 1-4: Continuous (no Binning, 2x2 Binning, 4x4 Binning, AOI) · · GEN-DIG-BRD/S required for digital data, syncs and control signals in RS-422 format. The connections between the 15-pin quad connector (DATA1) of the camera and the 100-pin connector of the GEN-DIG-BRD/S are as follows: SMD 4M15 (DATA1 15-pin quad-row connector) Pin name Pin no. D1A4+ D1A4D1A5+ D1A5D1A6+ D1A6D1A7+ D1A7D1A8+ D1A8D1A9+ D1A9D1A10+ D1A10D1A11+ D1A11D1B4+ D1B4D1B5+ D1B5D1B6+ D1B6D1B7+ D1B7D1B8+ D1B8D1B9+ D1B9D1B10+ D1B10D1B11+ D1B11D1HSYNC+ D1HSYNC D1VSYNC+ D1VSYNC D1GND+ D1GNDD1PCLK+ D1PCLK 09 10 11 12 13 14 17 18 19 20 21 22 23 24 25 26 40 39 38 37 36 35 34 33 32 31 52 51 50 49 48 47 58 57 56 55 45 46 60 59 GEN-DIG-BRD/S (GEN/CBL/OPEN connector) Pin name DATA, INPUT, 0+ DATA, INPUT, 0DATA, INPUT, 1+ DATA, INPUT, 1DATA, INPUT, 2+ DATA, INPUT, 2DATA, INPUT, 3+ DATA, INPUT, 3DATA, INPUT, 4+ DATA, INPUT, 4DATA, INPUT, 5+ DATA, INPUT, 5DATA, INPUT, 6+ DATA, INPUT, 6DATA, INPUT, 7+ DATA, INPUT, 7DATA, INPUT, 8+ DATA, INPUT, 8DATA, INPUT, 9+ DATA, INPUT, 9DATA, INPUT, 10+ DATA, INPUT, 10DATA, INPUT, 11+ DATA, INPUT, 11DATA, INPUT, 12+ DATA, INPUT, 12DATA, INPUT, 13+ DATA, INPUT, 13DATA, INPUT, 14+ DATA, INPUT, 14DATA, INPUT, 15+ DATA, INPUT, 15HSYNC, INPUT, + HSYNC, INPUT, VSYNC, INPUT, + VSYNC, INPUT, GROUND GROUND CLOCK, INPUT, + CLOCK, INPUT, - Pin no. 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 GEN-CID-031 4 Application Note: SMD 4M15 Interfacing non-standard cameras to Matrox Genesis February 16, 1998 Cabling Requirements (continued) · The connections between the 15-pin quad-row connector (DATA2) of the camera and the 100-pin connector of the GEN-DIG-BRD/S are as follows: SMD 4M15 (DATA2 15-pin quad-row connector) Pin name Pin no. D2A4+ D2A4D2A5+ D2A5D2A6+ D2A6D2A7+ D2A7D2A8+ D2A8D2A9+ D2A9D2A10+ D2A10D2A11+ D2A11D2B4+ D2B4D2B5+ D2B5D2B6+ D2B6D2B7+ D2B7D2B8+ D2B8D2B9+ D2B9D2B10+ D2B10D2B11+ D2B1109 10 11 12 13 14 17 18 19 20 21 22 23 24 25 26 40 39 38 37 36 35 34 33 32 31 52 51 50 49 48 47 GEN-DIG-BRD/S (GEN/CBL/OPEN connector) Pin name DATA, INPUT, 16+ DATA, INPUT, 16DATA, INPUT, 17+ DATA, INPUT, 17DATA, INPUT, 18+ DATA, INPUT, 18DATA, INPUT, 19+ DATA, INPUT, 19DATA, INPUT, 20+ DATA, INPUT, 20DATA, INPUT, 21+ DATA, INPUT, 21DATA, INPUT, 22+ DATA, INPUT, 22DATA, INPUT, 23+ DATA, INPUT, 23DATA, INPUT, 24+ DATA, INPUT, 24DATA, INPUT, 25+ DATA, INPUT, 25DATA, INPUT, 26+ DATA, INPUT, 26DATA, INPUT, 27+ DATA, INPUT, 27DATA, INPUT, 28+ DATA, INPUT, 29DATA, INPUT, 29+ DATA, INPUT, 30DATA, INPUT, 31+ DATA, INPUT, 31DATA, INPUT, 32+ DATA, INPUT, 32- Pin no. 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 The DCF(s) mentioned in this application note can be found on the MIL and MIL-Lite CD, or our FTP site (ftp. matrox. com). [. . . ] SL2 4JS Tel: +44 (0) 1753 665500 Fax: +44 (0) 1753 665599 France Matrox France SARL 2, rue de la Couture, Silic 225 94528 Rungis Cedex Tel: (0) 1 45-60-62-00 Fax: (0) 1 45-60-62-05 Germany Matrox GmbH Inselkammerstr. 8 D-82008 Unterhaching Germany Tel: 089/614 4740 Fax: 089/614 9743 Asia Pacific Matrox Asia Liaison Office Rm. 1901, 19/F, Workington Tower, 78 Bonham Strand E. , Sheung Wan, Hong Kong. [. . . ]