User manual MAXTOR MOMENTUS 5400.3 BLADE SERVER INSTALLATION REV A 4-2006

[. . . ] Follow these important mounting precautions when mounting the drive: · Allow a minimum clearance of 0. 030 inches (0. 76 mm) around the entire perimeter of the drive for cooling. (Reusing the existing screws may be acceptable provided the maximum screw penetration depth of 0. 098 inches is not exceeded. ) · Gently tighten the mounting screws (maximum torque: 4. 0 in-lb). · Four (4) threads (0. 080 inches) minimum screw engagement recommended. . 157 (3. 9878) . 399 (10. 135) 3. 945 +/-0. 0098 (100. 2 +/-. 25) 0. 490 +/- . 010 (12. 446 +/- . 254) 0. 680 +/- . 010 (17. 27 +/- . 254) Breather Hole Do not cover or seal. Handling precautions/electrostatic discharge protection · Disc drives are fragile. Keep the drive in the electrostatic discharge (ESD) bag until you are ready to install it to minimize handling damage. [. . . ] Some blade servers allow two drives to be installed and setup in a mirrored RAID configuration. If this is your situation, ensure that the storage capacities and speeds of the two drives are identical to avoid potential performance and reliability problems. 2. 430 (61. 722) . 160 (4. 06) Figure 2. Mounting dimensions--end, top, side, and bottom views Configuring the BIOS After completing the drive installation, restart your blade server according to your system documentation. If your server does not automatically detect your new drive, follow the steps below. While it restarts, run the system setup program (sometimes called BIOS or CMOS setup). This is usually done by pressing a special key, such as DELETE, ESC, or F1 during the startup process. Within the system setup program, instruct the blade server to auto detect your new drive. If your server still doesn't recognize your new drive, see the troubleshooting section on this sheet. Note. If these tips do not answer your question or solve the problem, contact your dealer or visit http://seatools. seagate. com to download SeaToolsTM disc diagnostics software and more troubleshooting advice. Seagate support services For online information about Seagate products, visit www. seagate. com or e-mail your disc questions to DiscSupport@Seagate. com. If you need additional help, call a Seagate technical support specialist. Before calling, note your system configuration and drive model number. Africa Australia Austria Belgium China* Denmark France Germany Hong Kong Hong Kong* India Indonesia Ireland Italy Malaysia Middle East *Chinese Warranty. To determine the warranty status of your Seagate disc drive, contact your place of purchase or visit our web site at www. seagate. com for more information. Run SeaTools to diagnose your drive before requesting a return authorization. In addition, please verify that your drive is defective by following the troubleshooting checklist in this guide. Seagate offers comprehensive customer support for all Seagate drives worldwide. Seagate customer service centers are the only facilities authorized to service Seagate drives. Drive return procedures vary depending on geographical location and are subject to current international trade regulations. Seagate assumes no responsibility for data lost during shipping or service. This model complies with the European Union requirements of the Electromagnetic Compatibility Directive 89/ 336/EEC of 03 May 1989 as amended by Directive 92/31/EEC of 28 April 1992 and Directive 93/68/EEC of 22 July 1993. Compliance of this drive, as a system component, was confirmed with a test system. The drive is not meant for external use (without properly designed enclosure, shielded I/O cable, etc. ). [. . . ] Follow the instructions provided on your screen. Troubleshooting If your drive is not working properly, these troubleshooting tips may help solve the problem. If your drive does not spin, check that the power connector and interface cable are securely attached. If the operating system does not recognize the drive, you need to load your host adapter drivers. Type fdisk/status to verify that your hard drive is present and recognized by the system. [. . . ]