User manual MAXTOR MOMENTUS 5400.2 INSTALLATION REV C 10-2004

[. . . ] Refer to your system manufacturer's support website for the most up-todate information. Read and follow all instructions regarding the proper steps to be taken when replacing the systems hard drive. Drive is master (or single drive) Drive is slave Cable select Figure 1. Jumper settings Drive mounting You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. Follow these important mounting precautions when mounting the drive: · Allow a minimum clearance of 0. 030 inches (0. 76 mm) around the entire perimeter of the drive for cooling. · Gently tighten the mounting screws (maximum torque: 4. 0 in-lb). [. . . ] This is usually done by pressing a special key, such as DELETE, ESC, or F1 during the startup process. Within the system setup program, instruct the system to auto detect your new drive. If your system still doesn't recognize your new drive, see the troubleshooting section on this sheet. Note. If these tips do not answer your question or solve the problem, contact your dealer or visit http://seatools. seagate. com to download SeaToolsTM disc diagnostics software and more troubleshooting advice. Seagate support services For online information about Seagate products, visit www. seagate. com or e-mail your disc questions to DiscSupport@Seagate. com. If you need additional help, call a Seagate technical support specialist. Before calling, note your system configuration and drive model number. Africa Australia Austria Belgium China* Denmark France Germany Hong Kong Hong Kong India Indonesia Ireland Italy Japan Malaysia Middle East *Mandarin Cantonese +1-405-324-4714 1800-14-7201 0 800-20 12 90 00 800-47324283 800-810-9668 00 800-47324283 00 800-47324283 00 800-47324283 800-90-0474 001-800-0830-1730 1-600-33-1104 001-803-1-003-2165 00 800-47324283 00 800-47324283 0034 800 400 554 1-800-80-2335 +1-405-324-4714 Netherlands New Zealand Norway Poland Spain Sweden Switzerland Singapore Taiwan* Thailand Turkey United Kingdom USA/Canada/ Latin America Other European countries 00 800-47324283 0800-443988 00 800-47324283 00 800-311 12 38 00 800-47324283 00 800-47324283 00 800-47324283 800-1101-150 00-800-0830-1730 001-800-11-0032165 00 800-31 92 91 40 00 800-47324283 1-800 SEAGATE or +1-405-324-4700 +1-405-324-4714 System manufacturer's operating system restore CD Refer to your mobile system documentation for specific instructions on restoring the operating system on your newly installed hard drive. Many computers require the use of an operating system restore CD, originally shipped with the system, to reload the operating system on the hard drive. Microsoft operating system installation instructions For detailed information about installing a Microsoft operating system on your new Seagate drive, refer to the Microsoft Knowledgebase article references below. To locate an article, go to http://support. microsoft. com and enter the article number in any search box on the Microsoft web site. For example, to view the Knowledgebase article for installing Windows XP on your new Seagate drive: 1. Operating system Windows XP Windows 2000/NT Windows Me/98/95 Microsoft Knowledgebase article numbers 313348 308209 (see also: 175761) 255867 (see also: 166172) Warranty. To determine the warranty status of your Seagate disc drive, contact your place of purchase or visit our web site at www. seagate. com for more information. Run SeaTools to diagnose your drive before requesting a return authorization. In addition, please verify that your drive is defective by following the troubleshooting checklist in this guide. Seagate offers comprehensive customer support for all Seagate drives worldwide. Seagate customer service centers are the only facilities authorized to service Seagate drives. Drive return procedures vary depending on geographical location and are subject to current international trade regulations. Seagate assumes no responsibility for data lost during shipping or service. This model complies with the European Union requirements of the Electromagnetic Compatibility Directive 89/ 336/EEC of 03 May 1989 as amended by Directive 92/31/EEC of 28 April 1992 and Directive 93/68/EEC of 22 July 1993. Compliance of this drive, as a system component, was confirmed with a test system. The drive is not meant for external use (without properly designed enclosure, shielded I/O cable, etc. ). [. . . ] I'm running Windows 98 and FDISK is not reporting the full capacity of my drive. You need to upgrade your version of FDISK if you are using the diskettes or CD that came with your original Windows 95 or 98 operating system. See Microsoft Knowledgebase article number: 263044 located at http://support. microsoft. com. ScanDisk is a utility located on your Windows startup diskette that scans the drive for defects. [. . . ]