User manual MAXTOR MOMENTUS

[. . . ] Product Manual Momentus ® 512-byte sector models ST9640320AS ST9500320AS ST9320310AS ST9250310AS ST9160316AS 4096-byte sector models ST9640322AS ST9400321AS ST9320312AS 100589392 Rev. C April 2010 Revision history Revision Date Sheets affected or comments Rev. C, April 2010 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Momentus and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. [. . . ] 3. 10. 6. 1 Operating vibration The maximum vibration levels that the drive may experience while meeting the performance standards specified in this document are specified below. 5­500 Hz 1. 0 G (0 to peak). Max displacement may apply below 10 Hz. 3. 10. 6. 2 Nonoperating vibration The maximum nonoperating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation are specified below. Max displacement may apply below 22 Hz. 14 Momentus Product Manual, Rev. C 3. 11 Acoustics Drive emission of sound is measured consistent with the ECMA-74 and its' referenced standards. Emission levels are reported as the total A-weighted sound power levels for steady state, idle, and active seek modes of operation. Table 6: Idle* 2. 3 bels (typ) 2. 5 bels (max) Drive A-weighted Sound Power Levels (SWL, BA) Seek 2. 4 bels (typ) 2. 6 bels (max) *During periods of drive idle, some offline activity may occur according to the S. M. A. R. T. specification, which may increase acoustic and power to operational levels. Test for Prominent Discrete Tones (PDTs) Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses the lower limit for the threshold curve* to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74 standards. *Defined as the median curve given by ISO 389-7 (Tf curve) minus 10dB at all frequencies. 3. 12 Electromagnetic immunity When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency (RF) environments defined in the following table: Table 7: Test Electrostatic discharge Radiated RF immunity Radio frequency environments Description Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV 80 to 2000 MHz, 10 V/m, 80% AM with 1 kHz sine 900 MHz, 3 V/m, 50% pulse modulation @ 200 Hz ± 1 kV on AC mains, ± 0. 5 kV on external I/O ± 1 kV differential, ± 2 kV common, AC mains 150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 kHz sine 1 A/m, 50Hz/60Hz, 3 axes 30% Reduction for 25 cycles >95% Reduction for 250 cycles >95%, 0. 5 cycles Performance level B A Reference standard EN 61000-4-2: 95 EN 61000-4-3: 96 ENV 50204: 95 EN 61000-4-4: 95 EN 61000-4-5: 95 EN 61000-4-6: 97 EN 61000-4-8: 97 EN 61000-4-11: 94 Electrical fast transient Surge immunity Conducted RF immunity Power Frequency H-field immunity Voltage dips, interrupts B B A A C C B Momentus Product Manual, Rev. C 15 3. 13 Reliability Specification 1 per 1014 bits read, max. <0. 48% Measurement type Nonrecoverable read errors Annualized Failure Rate (AFR) Load/Unload (U/UL) 25°C, 50% relative humidity 32°C, 80% relative humidity 5°C, 80% relative humidity 5°C, 10% relative humidity 55°C, 16% relative humidity Warranty 600, 000 software-controlled power on/off cycles 50, 000 hard power on/off cycles 600, 000 software-controlled power on/off cycles 50, 000 hard power on/off cycles To determine the warranty for a specific drive, use a web browser to access the following web page: http://www. seagate. com/www/en-us/support/warranty_&_returns_assistance You will be asked to provide the drive serial number, model number (or part number) and country of purchase. After submitting this information, the system will display the warranty information for your drive. 3. 14 3. 14. 1 Agency certification Safety certification These products are certified to meet the requirements of UL60950-1, CSA60950-1 and EN60950 and so marked as to the certify agency. 3. 14. 2 Electromagnetic compatibility Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility Directive (2004/108/EC) as put into place 20 July 2007. Testing is performed to the levels specified by the product standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN 55024. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators should confirm EMC compliance and provide CE marking for their products. 16 Momentus Product Manual, Rev. C Korean RRL If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Communications Commission, Republic of Korea. These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recognized lab. · Certificate number: STX-Momentus (B) · Trade name or applicant: Seagate Technology LLC · Manufacturing date: May 25, 2009 (Date of Certification) · Manufacturer/nationality: USA, Singapore and China Australian C-Tick (N176) If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZ CISPR22 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication Authority (ACA). [. . . ] Retired Multiword DMA active and modes supported (see note following this table) Advanced PIO modes supported (modes 3 and 4 supported) Minimum multiword DMA transfer cycle time per word (120 nsec) Recommended multiword DMA transfer cycle time per word (120 nsec) Minimum PIO cycle time without IORDY flow control (240 nsec) Minimum PIO cycle time with IORDY flow control (120 nsec) ATA-reserved Queue depth Serial ATA capabilities ATA-reserved Serial ATA features supported Serial ATA features enabled Major version number Minor version number Command sets supported Command sets supported Command sets support extension Command sets enabled Command sets enabled Command sets enable extension Ultra DMA support and current mode (see note following this table) Security erase time Enhanced security erase time Master password revision code Hardware reset value (see description following this table) Auto acoustic management setting ATA-reserved Value xxxxH xxxxH 0FFFFFFFh 62 63 64 65 66 67 68 69­74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 92 93 94 95­99 0000H xx07H 0003H 0078H 0078H 00F0H 0078H 0000H 001FH 0508H 0000H 0048H 0040H 003EH 0028H 306BH 4001H 4000H 30xxH 0001H 4000H xx7FH 0000H 0000H FFFEH xxxxH xxxxH 0000H 28 Momentus Product Manual, Rev. C Word 100­ 103 Description Total number of user-addressable LBA sectors available (see Section 3. 2 for related information) These words are required for drives that support the 48-bit addressing feature. ATA-reserved Free Fall Protection support (bit 5) Free Fall Protection enable/disable (bit 5) ATA reserved Security status Seagate-reserved ATA-reserved Integrity word Value 0FFFFFFFh 104­ 118 119 120 121­ 127 128 129­ 159 160­ 254 255 0000H 1 = Free Fall Protection supported 0 = Free Fall Protection not supported 1 = Free Fall Protection feature is enabled 0 = Free Fall Protection feature is disabled 0000H 0001H xxxxH 0000H xxA5H Note. See the bit descriptions below for words 63, 88, and 93 of the Identify Drive data: Description (if bit is set to 1) Bit 0 1 2 8 9 10 Bit 0 1 2 3 4 5 6 8 9 10 11 12 13 14 Word 63 Multiword DMA mode 0 is supported. Ultra DMA mode 5 is supported Ultra DMA mode 6 is supported Ultra DMA mode 0 is currently active. [. . . ]