User manual MAXTOR MEDIALIST 2132

[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist 2132 (ST32132A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ATA Interface Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist 2132 (ST32132A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ATA Interface Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Remove all the jumper settings. 2. 4. 2 Cable-select option Computers that use cable-select determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. · The drive plugged into the I/O connector that carries the CSEL signal is the master. · The drive plugged into the I/O connector that does not carry the CSEL signal is the slave. To configure drives for computers that use cable-select: · Install jumpers on pins 3 and 4 as shown in Figure 4 above. · Connect the drives to the cable as shown in Figure 5 on page 19. Medalist 2132 Product Manual, January 1997 19 Slave CSEL not carried to pin 28 of this connector Master Pin 28 grounded at computer Computer Figure 5. Connecting cable-selected drives 2. 4. 3 Diagnostics Jumper The diagnostics jumper activates a drive feature called EZConfig. EZConfig allows the advanced user to enable, disable or change the size of the read and write cache and to configure PIO mode 4 capability. Place jumpers on pins 1 and 2 and on pins 5 and 6 of the options jumper block. If you have more than one hard drive, remove the drive you do not want to test. Select auto-detect or an available drive type if no hard drive is defined. When you are done running EZConfig, turn off your computer, remove the drive and place the master/slave jumpers back on the appropriate pins. Reinstall the drive and reconfigure the system BIOS setup. 20 Medalist 2132 Product Manual, January 1997 2. 5 Mounting the drive You can mount the drive in any orientation using either the bottom or the side mounting holes as described below. Insert four mounting screws not more than 0. 20 inches (6 full turns) into the drive frame. Insert four mounting screws not more than 0. 13 inches (4 full turns) into the drive frame. To prevent damage to the drive: · Use only mounting screws of the correct size and length. · Lightly tighten the mounting screws--do not apply more than 6 inch-pounds of torque. Figure 6 on page 21 shows the dimensions in inches and millimeters. Medalist 2132 Product Manual, January 1997 21 Six 6-32 UNC-2B mounting holes 1. 000 max (25. 4) 2. 362 ± 0. 010 (59. 995. ± 0. 254) 4. 000 ± 0. 010 (101. 60 ± 0. 254) 0. 630 ± 0. 025 (16. 002 ± 0. 635) 0. 250 ± 0. 010 (6. 350 ± 0. 254) 5. 77 max (146. 56) 2. 375 ± 0. 030 (60. 325 ± 0. 762) 1. 750 ± 0. 010 (44. 450 ± 0. 254) 3. 750 ± 0. 030 (95. 250 ± 0. 762) Four 6-32 UNC-2B mounting holes Figure 6. Standard mounting dimensions 4. 02 max (102. 108) 22 Medalist 2132 Product Manual, January 1997 Medalist 2132 Product Manual, January 1997 23 3. 0 ATA interface The drive uses an ATA interface. The interface is in compliance with ANSI ATA (AT Attachment) Interface X3. 221, Rev. 2. 0; SFF 8019: Identify Drive Data for Drives Under 8 GB and Draft Proposal American National Standards AT Attachment Interface X3. 310-948D, Rev. [. . . ] status Medalist 2132 Product Manual, January 1997 35 3. 5 Drive Security Commands The drive security commands provide a password-based security system to prevent unauthorized access to a disc drive. During manufacturing, the master password, SEAGATE, is set for the drive, and the lock function is disabled. The system manufacturer or dealer may set a new user password using the Security Set Password command (F1H) without enabling the lock function. Before a user password is entered, the drive rejects all security commands except Security Set Password. [. . . ]