User manual MAXTOR MEDIALIST 1640 INSTALLATION

[. . . ] Product Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . © 1995 Seagate Technology, Inc. A, January 1996 Seagate, Seagate Technology and the Seagate logo are registered trademarks of Seagate Technology, Inc. Other product names are trademarks or registered trademarks of their owners. [. . . ] This equipment generates and uses radio frequency energy and, if not installed and used in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television, which can be determined by turning the equipment on and off, you are encouraged to try one or more of the following corrective measures: · Reorient the receiving antenna. · Plug the equipment into a different outlet so that the receiver and computer are on different branch outlets. If necessary, you should consult your dealer or an experienced radio/television technician for additional suggestions. You may find helpful the following booklet prepared by the Federal Communications Commission: How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Superintendent of Documents, US Government Printing Office, Washington, DC 20402. This digital apparatus does not exceed the Class B limits for radio noise emissions from computer equipment as set out in the radio interference regulations of the Canadian Department of communications. Le présent appareil numérique német pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par le Ministère des Communications du Canada. 16 Medalist 1640 and 2140 Product Manual, January 1996 Sicherheitsanleitung 1. Das Gerrät ist ein Einbaugerät, das für eine maximale Umgebungstemperatur von 55°C vorgesehen ist. Zur Befestigung des Laufwerks werden 4 Schrauben 6-32 UNC-2A benötigt. Bei seitlicher Befestigung darf die maximale Länge der Schrauben im Chassis nicht mehr als 5, 08 mm und bei Befestigung an der Unterseite nicht mehr als 5, 08 mm betragen. Als Versorgungsspannugen werden benötigt: +5V ± 5% 0, 6A +12V ± 5% 0, 8A (1, 9A fur ca. Alle Arbeiten auf dem Festplatte dürfen nur von Ausgebildetem Servicepersonal durchgeführt werden. Der Einbaudes Drives muss den Anforderungen gemäss DIN IEC 950V DC 0805/05. 90 entsprechen. Medalist 1640 and 2140 Product Manual, January 1996 17 2. 0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 2. 1 Handling and static-discharge precautions After you unpack the drive, and before you install it in a system, be careful not to damage it through mishandling or static discharge. Wool and synthetic clothing, carpet, plastic and styrofoam are contributors to static charge buildup. This charge is released when you touch another conductor and can damage sensitive components in the drive. Observe the following standard handling and static-discharge precautions: Caution: · Keep the drive in its static-shielded bag until you are ready to complete the installation. Do not attach any cables to the drive while it is in its static-shielded bag. · Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure. · Always rest the drive on a padded, antistatic surface until you mount it in the computer. [. . . ] The upper 5 bits of this value define the type of data transfer, and the lower 3 bits encode the mode value. This changes word 63 of the Identify Drive command to the mode you enter in the Sector Count register. The table on the next page identifies allowable transfer types values: Medalist 1640 and 2140 Product Manual, January 1996 33 Data transfer mechanism Mechanism name PIO Transfer Mode (default: Set PIO Mode = 2) PIO Transfer Mode: Set PIO Mode = 2 PIO Flow Control Transfer Mode: Set PIO Mode = 0 PIO Flow Control Transfer Mode: Set PIO Mode = 1 PIO Flow Control Transfer Mode: Set PIO Mode = 2 PIO Flow Control Transfer Mode: Set PIO Mode = 3 PIO Flow Control Transfer Mode: Set PIO Mode = 4 Multiword DMA Mode Multiword DMA Mode Multiword DMA Mode Reserved Mode value 2 2 0 1 2 3 4 0 1 2 ---- Transfer types value Data Lower 3 bits Upper 5 bits 00000 00000 00001 00001 00001 00001 00001 00100 00100 00100 01000 000 001 000 001 010 011 100 000 001 010 nnn 3. 2. 3 Idle and Set Idle Timer (FAH) This is a Seagate-unique power command. When the drive receives this command, it asserts Busy in the Host Status register, initiates entry into Idle mode, negates Busy and generates an interrupt. [. . . ]