User manual MAXTOR ES10

[. . . ] CAMERA INTERFACE APPLICATION NOTE REDLAKE MASD (KODAK) ES1. 0 JUNE 19, 2001 Basics about the camera MATROX PULSAR Camera Descriptions § § § § § § 1008 × 1018 × 8/10-bit @ 15/30 fps. 20 MHz pixel clock rate. Mode of operations as per Matrox Imaging (in parentheses as per camera manufacturer) Basics about the interface modes Interface Modes § Pseudo-continuous § Asynchronous reset (Trigger, Control) Camera Interface Briefs § § § § 1008 × 1018 × 8-bit @ 15 fps. [. . . ] PIX DATA EXPOSE Specifics about the interface modes Camera Interface Details Mode 1: Pseudo-continuous TTL EXTERNAL TRIGGER *Matrox Pulsar RS-422 digital data input board § Frame Rate: Matrox Pulsar receives the continuous video from the camera at 15 frames per second. § Exposure time: Exposure time is controlled by the Remote Panel software. § Remote Panel software settings: Settings for this mode are as follows: DEF GAB BKB BKE MDE EXE 15. 096 STP P TRM P TRS AIA TRE 1 RDM 2* TPD 255 TPW 5 DGN 2 on -22 0 0 CS * Single channel = 1, dual channel = 2 Mode 2: Asynchronous Reset (Trigger) § Frame rate: The frame rate is determined by the frequency of the external trigger signal. § Exposure time: Exposure time is controlled by the Remote Panel software. § Remote Panel software settings: Settings for this mode are as follows: DEF GAB BKB BKE MDE EXE STP TRM TRS TRE RDM ** TPD 255 TPW 5 DGN 2 on -22 0 0 * 15. 096 P P AIA 1 * Trigger mode = TR, Control mode = CD **Single channel = 1, dual channel = 2 Mode 2: Asynchronous Reset (Control) § Frame rate: The frame rate is determined by the frequency of the external trigger signal. § Exposure time: The width (rising to falling edge) of the EXPOSURE1 (EXPOSE) signal initiates and controls the exposure. The exposure time can be modified in the DCF using Matrox Intellicam or with the MIL MdigControl() function. § Remote Panel software settings: Settings for this mode are as follows: DEF GAB BKB BKE MDE EXE STP TRM TRS TRE RDM ** TPD 255 TPW 5 DGN 2 on -22 0 0 * 15. 096 P P AIA 1 * Trigger mode = TR, Control mode = CD **Single channel = 1, dual channel = 2 PUL-CID-038 2 CAMERA INTERFACE APPLICATION NOTE REDLAKE MASD (KODAK) ES1. 0 JUNE 19, 2001 Cabling details for this interface mode MATROX PULSAR Cabling Requirements Mode 1: Pseudo-continuous § Cable: DBHD68-TO-OPEN (open ended) cable required for video, synchronization and control signals. § Connection: Connections between the 68-pin connector of the camera and the 68-pin connectors of the Matrox Pulsar are as follows: PULSAR/DIG/MOD (68-pin connector) Pin name Pin no. REDLAKE MASD ES 1. 0 (68-pin connector) Pin name Pin no. DATA7+ 10 MSB+ 02 DATA744 MSB36 DATA6+ 11 MSB-1+ 03 DATA645 MSB-137 DATA5+ 13 MSB-2+ 04 DATA547 MSB-238 DATA4+ 14 MSB-3+ 05 DATA448 MSB-339 DATA3+ 15 MSB-4+ 06 DATA349 MSB-440 DATA2+ 16 MSB-5+ 07 DATA250 MSB-541 DATA1+ 19 MSB-6+ 08 DATA153 MSB-642 DATA0+ 20 MSB-7+ 09 DATA054 MSB-743 CLKIN+ 29 PIX DATA STRB+ 29 CLKIN63 PIX DATA STRB63 HSYNC+ 26 LINE ENA+ 26 HSYNC60 LINE ENA60 VSYNC+ 25 FRME ENA+ 25 VSYNC59 FRME ENA59 EXPOSURE1+ 30* EXPOSE+ 30* EXPOSURE164* EXPOSE64* TTL_USR0 31 C0 31 TTL_USR1 32 MC1 32 TTL_USR2 33 MC2 33 GROUND 01 -GROUND 01 GROUND 12 -GROUND 12 GROUND 34 -GROUND 34 GROUND 35 -GROUND 35 GROUND 46 -GROUND 46 GROUND 68 -GROUND 68 * Connection not necessary for this mode however allows this cable to be used for both modes. [. . . ] Contact your local sales representative or Matrox Sales office or Matrox Imaging Applications at 514-822-6061 for assistance. Corporate headquarters: Canada and U. S. A. Dorval, Quebec H9P 2T4 Canada Tel: (514) 685-2630 Fax: (514) 822-6273 PUL-CID-038 [. . . ]