User manual MAXTOR DIAMONDMAX 23 SERIAL ATA REV C 2-2009

[. . . ] Product Manual DiamondMax 23 Serial ATA STM31000528AS STM3750528AS STM3500418AS STM3320418AS STM3250318AS STM3160318AS 100539323 Rev. C February 2009 Revision history Revision Date Sheets affected or comments Rev. fc, 1, 3, 6, 8, 10-11, 15, 24 and 30. Copyright © 2009 Seagate Technology LLC. C February 2009 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. [. . . ] AFR and MTBF specifications are based on the following assumptions for desktop personal computer environments: · 2400 power-on-hours per year. · Temperatures outside the specifications in Section 2. 8 may reduce the product reliability. Operation at excessive I/O duty cycle may degrade product reliability. The desktop personal computer environment of power-on-hours, temperature, and I/O duty cycle affect the product AFR and MTBF. The AFR and MTBF will be degraded if used in an enterprise application Nonrecoverable read errors Annualized Failure Rate (AFR) Contact start-stop cycles Warranty 1 per 1014 bits read, max 0. 32% (nominal power, 25°C ambient temperature) 50, 000 cycles (at nominal voltage and temperature, with 60 cycles per hour and a 50% duty cycle) To determine the warranty for a specific drive, use a web browser to access the following web page: support. seagate. com/customer/warranty_validation. jsp From this page, click on the "Verify Your Warranty" link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. None required. Preventive maintenance 2. 12 2. 12. 1 Agency certification Safety certification These products are certified to meet the requirements of UL60950-1, CSA60950-1 and EN60950 and so marked as to the certify agency. 2. 12. 2 Electromagnetic compatibility Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility Directive (2004/108/EC) as put into place 20 July 2007. Testing is performed to the levels specified by the product standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN 55024. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators should confirm EMC compliance and provide CE marking for their products. DiamondMax 23 Serial ATA Product Manual, Rev. C 17 Korean RRL If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Communications Commission, Republic of Korea. These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recognized lab. · Family name: DiamondMax 23 · Certificate number: STX-720012 (B) Australian C-Tick (N176) If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZ CISPR22 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication Authority (ACA). 2. 12. 3 FCC verification These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an external device). As such, each drive is considered to be a subassembly even when it is individually marketed to the customer. As a subassembly, no Federal Communications Commission verification or certification of the device is required. Seagate has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disk drive, motherboard, power supply, etc. ) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is likely to result in interference to radio and television reception. [. . . ] You must have a recent BIOS or software package that supports S. M. A. R. T. Return Status Code in features register D0H D2H D3H D4H D5H D6H D8H D9H DAH Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x 04 (abort) is written to the Error register. 34 DiamondMax 23 Serial ATA Product Manual, Rev. C 5. 0 Seagate Technology support services Online services IInternet For information regarding Seagate products and services, visit www. seagate. com. Worldwide support is available 24 hours daily by email for your questions. [. . . ]