User manual MAXTOR CVM30

[. . . ] Interfacing non-standard cameras to Matrox Pulsar JAI CV-M30 Camera Interface Overview · · · · · · Application Note: October 29, 1996 768 x 494 x 8-bit Analog video output Interlaced or non-interlaced Internal composite sync Internal exposure control Modes of operations: continuous mode (normal or double speed), continuous partial scanning mode (1/2 and 1/3 both at normal or double speed) and asynchronous mode Camera Interface Details 1. Continuous mode (Double speed, interlaced) JAI CV-M30 · · · · · · · Video 752 x 484 x 8-bit @60 fps Interlaced Analog (composite) video output Internal exposure control (normal shutter mode) Double speed mode Continuous video DCF used: CVM30S. DCF Matrox Pulsar 2. [. . . ] Continuous Modes 1 through 8 · · Application Note: October 29, 1996 · IMG-7W2-TO-1BNC required Video input BNC of IMG-7W2-TO 1BNC cable should be connected to VIDEO OUT BNC connector of camera The switches on the rear panel of the camera must be correctly configured, see SPECIAL CONSIDERATIONS for each mode's switch configuration 2. Mode 9 Asynchronous reset mode (trigger mode) · · · · IMG-7W2-TO-5BNC cable and PLS-TTL-CABLE required Video input of BNC of IMG-7W2-TO-5BNC cable should be connected to VIDEO OUT BNC connector of camera The switches on the rear panel of the camera must be correctly configured, see SPECIAL CONSIDERATIONS for this mode's switch configuration The connections between the DB-37 connector of the PLS-TTL-CABLE and the 6pin male HIROSE connector of the camera are as follow: PLS-TTL-CABLE (DB-37 connector) connector) Pin name Pin no. 9 11 6 Pin name TRIGGER VALID (WEN) GROUND 5 6 3 · TTL external trigger source should be connected to the TTL trigger input of IMG7W2-TO-5BNC cable Special Considerations Switch settings (switches on rear panel of camera) for all 9 modes 1. continuous mode (double speed, non-interlaced) ON · · · · · · · 1 2 3 4 5 6 7 ED2 ED1 ED0 LM2 RM1 LM1 TRSW shutter speed shutter speed shutter speed scanning mode scanning speed scanning mode reset mode · · · · · · · 1 2 3 4 5 6 7 ED2 ED1 ED0 LM2 RM1 LM1 TRSW shutter speed shutter speed shutter speed scanning mode scanning speed scanning mode reset mode PUL-CID-030 4 Interfacing non-standard cameras to Matrox Pulsar JAI CV-M30 3. continuous mode (normal speed, interlaced) OFF ON OFF Application Note: October 29, 1996 4. continuous mode (normal speed, non-interlaced) ON · · · · · · · 1 2 3 4 5 6 7 ED2 ED1 ED0 LM2 RM1 LM1 TRSW shutter speed shutter speed shutter speed scanning mode scanning speed scanning mode reset mode · · · · · · · 1 2 3 4 5 6 7 ED2 ED1 ED0 LM2 RM1 LM1 TRSW shutter speed shutter speed shutter speed scanning mode scanning speed scanning mode reset mode 5. continuous partial scanning (1/3) mode (normal speed) OFF ON · · · · · · · 1 2 3 4 5 6 7 ED2 ED1 ED0 LM2 RM1 LM1 TRSW shutter speed shutter speed shutter speed scanning mode scanning speed scanning mode reset mode · · · · · · · 1 2 3 4 5 6 7 ED2 ED1 ED0 LM2 RM1 LM1 TRSW shutter speed shutter speed shutter speed scanning mode scanning speed scanning mode reset mode 7. continuous partial scanning (1/3) mode (double speed) OFF ON · · · · · · · 1 2 3 4 5 6 7 ED2 ED1 ED0 LM2 RM1 LM1 TRSW shutter speed shutter speed shutter speed scanning mode scanning speed scanning mode reset mode · · · · · · · 1 2 3 4 5 6 7 ED2 ED1 ED0 LM2 RM1 LM1 TRSW shutter speed shutter speed shutter speed scanning mode scanning speed scanning mode reset mode 9. asynchronous reset mode OFF ON · · · · · · · · 1 2 3 4 5 6 7 8 ED2 ED1 ED0 LM2 RM1 LM1 TRSW AGC shutter speed shutter speed shutter speed scanning mode scanning speed scanning mode reset mode AGC mode The internal exposure control can be changed by the first 3 switches PUL-CID-030 5 Interfacing non-standard cameras to Matrox Pulsar JAI CV-M30 Asynchronous reset mode (trigger mode) · · Application Note: October 29, 1996 · · · The shutter mode is selected by using the SW1 switches on the rear of the camera. In asynchronous reset mode, the switch RM1 should always be set to the ON position since this mode can only work in normal mode. Once in asynchronous reset mode (by setting the TRSW switch to ON), the exposure time is set using switches #1, #2 and #3 on the rear panel of the camera. In "normal speed" mode, exposure times range from (1/60)s to (1/10 000)s. [. . . ] SL2 4JS Tel: +44 (0) 1753 665500 Fax: +44 (0) 1753 665599 France Matrox France SARL 2, rue de la Couture, Silic 225 94528 Rungis Cedex Tel: (0) 1 45-60-62-00 Fax: (0) 1 45-60-62-05 Germany Matrox GmbH Inselkammerstr. 8 D-82008 Unterhaching Germany Tel: 089/614 4740 Fax: 089/614 9743 Asia Pacific Matrox Asia Liaison Office Rm. 1901, 19/F, Workington Tower, 78 Bonham Strand E. , Sheung Wan, Hong Kong. [. . . ]