User manual MAXTOR CHEETAH 10K.7 SCSI

[. . . ] Users Guide Cheetah 10K. 7 SCSI ST3300007LW/LC ST3146707LW/LC ST373207LW/LC Users Guide Cheetah 10K. 7 SCSI ST3300007LW/LC ST3146707LW/LC ST373207LW/LC ©2003-2005, Seagate Technology LLC All rights reserved Publication number: 100260915, Rev. D July 2005 Seagate and Seagate Technology are registered trademarks of Seagate Technology LLC. Cheetah, SeaTools, SeaFONE, SeaBOARD, SeaTDD, and the Wave logo are either registered trademarks or trademarks of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners. [. . . ] Packaged Disc drives shipped as loose load (not palletized) general freight will be packaged to withstand drops from heights as defined below. For additional details refer to Seagate specifications 30190-001 (under 100 lbs/45 kg) or 30191-001 (over 100 lbs/45 Kg). Package size Packaged/product weight Drop height <600 cu in (<9, 800 cu cm) 600-1800 cu in (9, 800-19, 700 cu cm) >1800 cu in (>19, 700 cu cm) >600 cu in (>9, 800 cu cm) Any 0-20 lb (0 to 9. 1 kg) 0-20 lb (0 to 9. 1 kg) 20-40 lb (9. 1 to 18. 1 kg) 60 in (1524 mm) 48 in (1219 mm) 42 in (1067 mm) 36 in (914 mm) Drives packaged in single or multipacks with a gross weight of 20 pounds (8. 95 kg) or less by Seagate for general freight shipment shall withstand a drop test from 48 inches (1, 070 mm) against a concrete floor or equivalent. Cheetah 10K. 7 SCSI Product Manual, Rev. Operating - normal The drive as installed for normal operation, shall comply with the complete specified performance while subjected to continuous vibration not exceeding 5-500 Hz @ 1. 0 G (zero to peak) Vibration may be applied in the X, Y, or Z axis. Operating - abnormal The drive as installed for normal operation shall not incur physical damage while subjected to periodic vibration not exceeding: 15 minutes of duration at major resonant frequency 5-500 Hz @ 1. 5 G (X, Y, or Z axis, zero to peak) Vibration occurring at these levels may degrade operational performance during the abnormal vibration period. Specified operational performance will continue when normal operating vibration levels are resumed. Non-operating The limits of non-operating vibration shall apply to all conditions of handling and transportation. The drive shall not incur physical damage or degraded performance as a result of continuous vibration not exceeding 5-22 Hz @ 0. 040 inches (1. 02 mm) displacement (zero to peak) 22-500 Hz @ 3. 00 G Vibration may be applied in the X, Y, or Z axis. Non-operating translational random flat profile 10 - 400 Hz 6. 4. 5 Air cleanliness 1. 2 GRMS 1. 2 GRMS 0. 5 GRMS The drive is designed to operate in a typical office environment with minimal environmental control. 6. 4. 6 Corrosive environment Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated testing cannot duplicate every potential application environment. Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulcanized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives. Cheetah 10K. 7 SCSI Product Manual, Rev. D 37 6. 4. 7 Acoustics Sound power during idle mode shall be 3. 3 bels typical, or better, when measured to ISO 7779 specification. There will not be any discrete tones more than 10 dB above the masking noise on typical drives when measured according to Seagate specification 30553-001. There will not be any tones more than 24 dB above the masking noise on any drive. 6. 4. 8 Electromagnetic susceptibility See Section 2. 1. 2. 6. 5 Mechanical specifications The following nominal dimensions are exclusive of the decorative front panel accessory. Refer to Figures 16 and 17 for detailed mounting configuration dimensions. See Section 8. 4, "Drive mounting. " Height: Width: Depth: Weight: 1. 000 in 4. 000 in 5. 75 in 1. 6 pounds 25. 4 mm 101. 6 mm 146. 05 mm 0. 726 kilograms 38 Cheetah 10K. 7 SCSI Product Manual, Rev. D K S // T -Z[1] H B Notes: R -X[1] Mounting holes are 6-32 UNC 2B, three on each side and four on the bottom. [. . . ] to 5:00 P. M. , Saturday (Eastern time). 88 Cheetah 10K. 7 SCSI Product Manual, Rev. D European support services For presales and technical support in Europe, dial the Seagate Service Center toll-free number for your specific location. If your location is not listed here, dial our presales and technical support call center at +1-405324-4714 from 8:00 A. M. The presales and technical support call center is located in Oklahoma City, USA. [. . . ]