User manual MAXTOR CAD41024A

[. . . ] Application Note: DALSA CA-D4-1024A · · · · · Interfacing non-standard cameras to Matrox Pulsar April 13, 1998 Camera Descriptions 1024 x 1024 x 8-bit Single or dual digital video output (RS-422). Exposure control Continuous, asynchronous reset with single video output Interface Modes N. B. [. . . ] Matrox Pulsar receiving RS-422 HSYNC (LVAL) and RS-422 VSYNC (FVAL) signals from camera. DCF used: CAD4DA. DCF Application Note: DALSA CA-D4-1024A Interfacing non-standard cameras to Matrox Pulsar April 13, 1998 Cabling Requirements Mode 1 : Continuous mode · The connections between the two 20-pin dual-row connector (0S1) of the camera and the 68-pin connector of the PULSAR/CBL/OPEN are as follows: DALSA CA-D4-1024A (OS1 20-pin IDC connector) Pin name Pin no. D7 1 D7B 2 D6 3 D6B 4 D5 5 D5B 6 D4 7 D4B 8 D3 9 D3B 10 D2 11 D2B 12 D1 13 D1B 14 D0 15 D0B 16 STROBE B 17 STROBE 18 LVAL 19 LVAL B 20 PULSAR/DIG/MOD (PULSAR/CBL/OPEN connector) Pin name Pin no. DATA, INPUT, 7+ 10 DATA, INPUT, 744 DATA, INPUT, 6+ 11 DATA, INPUT, 645 DATA, INPUT, 5+ 13 DATA, INPUT, 547 DATA, INPUT, 4+ 14 DATA, INPUT, 448 DATA, INPUT, 3+ 15 DATA, INPUT, 349 DATA, INPUT, 2+ 16 DATA, INPUT, 250 DATA, INPUT, 1+ 19 DATA, INPUT, 153 DATA, INPUT, 0+ 20 DATA, INPUT, 054 CLOCK, INPUT, + 29 CLOCK, INPUT, 63 HYSNC, INPUT, + 26 HSYNC, INPUT, 60 · The connections between the two 20-pin dual-row connector (0S2) of the camera and the 68-pin connector of the PULSAR/CBL/OPEN are as follows: DALSA CA-D4-1024A (OS2 20-pin IDC connector) Pin name Pin no. FVAL 17 FVALB 18 PULSAR/DIG/MOD (PULSAR/CBL/OPEN connector) Pin name Pin no. VSYNC, INPUT, + 25 VSYNC, INPUT, 59 · The connections between the DB-25 connector on the rear panel of the camera and the 68pin connector of the PULSAR/CBL/OPEN are as follows: DALSA CA-D4-1024A (DB-25 male connector) Pin name Pin no. EXSYNC 17* EXSYNCB 04* PRIN 05 to 13 (jumper) PRINB 18 to 7 (jumper) BIN 1 to 8 (jumper) BIN B 14 to 24 (jumper) PULSAR/DIG/MOD (PULSAR/CBL/OPEN connector) Pin name Pin no. EXPOSURE, OUTPUT, 1+ 30 EXPOSURE, OUTPUT, 164 PUL-CID-043 2 Application Note: DALSA CA-D4-1024A Interfacing non-standard cameras to Matrox Pulsar April 13, 1998 Cabling Requirements (continued) · The connections between the DB-25 connector on the rear panel of the camera and the power supply are as follows: DALSA CA-D4-1024A (DB-25 female connector) Pin no. Pin name 8 +5V 9 +28V 12 -5V 13 +5V 21 +28V 22 -5V 25 -15V POWER SUPPLY +5V +28V -5V -15V 7 GROUND 11, 20, 24 GROUND GROUND GROUND NOTE: it is very important that all the GROUNDs of the camera are connected to the POWER SUPPLY GROUND, which in turn must be connected to the GROUND of the Matrox Pulsar. Mode 2: Asynchronous reset mode · IMG-7W2-TO-5BNC cable required for TTL external trigger signal source and PULSAR/DIG/MOD required for digital data, sync and control signals in RS-422 format. [. . . ] SL2 4JS Tel: +44 (0) 1753 665500 Fax: +44 (0) 1753 665599 France Matrox France SARL 2, rue de la Couture, Silic 225 94528 Rungis Cedex Tel: (0) 1 45-60-62-00 Fax: (0) 1 45-60-62-05 Germany Matrox GmbH Inselkammerstr. 8 D-82008 Unterhaching Germany Tel: 089/614 4740 Fax: 089/614 9743 Asia Pacific Matrox Asia Liaison Office Rm. 1901, 19/F, Workington Tower, 78 Bonham Strand E. , Sheung Wan, Hong Kong. [. . . ]