User manual MAXTOR BARRACUDA 7200.8 INSTALLATION REV A 11-2004

[. . . ] To enable cable select, set a Options jumper block jumper on pins 5 and 6. *Master or single drive · Alternate capacity jumper: Drives Drive is slave with a 40-Gbyte capacity or greater Master with non ATAcompatible slave are limited to 32 Gbytes. Use this *Cable select jumper only if you have a legacy sysAlternate capacity. tem with a BIOS that does not support Limits drive capacity large capacity disc drives. [. . . ] · Go to http://support. seagate. com for additional information. Master Slave Pin 1 Breather filter hole precaution drive connector. Secure the drive using four 6-32 UNC mounting screws in either the side-mounting or bottom-mounting holes. Insert the screws no more than 0. 20 inches (5. 08 mm) into the bottom-mounting holes and no more than 0. 14 inches (3. 55 mm) into the side-mounting holes. Attach the interface connector and the power connector to the drive. Configuring the BIOS Close your computer case and restart your computer. If your computer does not automatically detect your new drive, follow the steps below. While the computer restarts, run the System Setup program (sometimes called BIOS or CMOS setup). This is usually done by pressing a special key, such as DELETE, ESC, or F1 during the startup process. Within the System Setup program, instruct the system to auto detect your new drive. Enable LBA and UDMA modes, if available and then save the settings and exit the Setup program. If your system still doesn't recognize your new drive, see the troubleshooting section on the back of this sheet. Caution. This hole has two purposes: · To allow condensation inside the hard disc to escape · To allow air pressure inside the hard disc to equalize with ambient pressure If this hole is covered, sealed, or penetrated by any object, the drive reliability may be compromised and could lead to permanent damage--doing so voids the warranty. Handling precautions/electrostatic discharge protection · Disc drives are fragile. Handle the drive only by the edges or frame. BIOS Settings Drive Model Formatted Gbytes ST3400832A 400. 0 ST3300831A 300. 0 ST3250823A 250. 0 ST3200826A 200. 0 *One sector equals 512 bytes. Total Sectors* 781, 422, 768 586, 072, 368 488, 397, 168 390, 721, 968 Cache 8 Mbytes 8 Mbytes 8 Mbytes 8 Mbytes Preparing the drive using DiscWizard Installing a single drive If you are installing a single drive, we recommend using DiscWizard to automatically partition and format your drive. During the download, the Diskette Creator creates a portable bootable diskette. Boot your computer from the Windows operating system CD-ROM or from your system startup diskette with the Windows CD loaded. Installing a slave drive If you are installing a second drive, or slave, to your system, use the DiscWizard software available at www. seagate. com. If you do not want to install your drive using either DiscWizard or Disk Manager, see "Standard Microsoft Installation" below to partition and format your drive. 6. Verify that your system is ATA/100 compatible with the UDMA mode setting. Some legacy BIOS cause hangs on startup or other problems if it is not ATA/100 compatible. For more information, see the earlier section on the Ultra ATA/100 requirements. In addition, some legacy BIOS may cause a hang due to the large drive capacity. Consider using the alternate capacity jumper if it is available on your drive model. Use the alternate capacity jumper if your computer does not support higher capacity drives. [. . . ] Zur Befestigung des Lufwerks werden 4 Schrauben 6-32 UNC-2A benötigt. Bei seitlicher Befestigung darf die maximale Länge der Schrauben im Chassis nicht merh als 3, 3 mm und bei Befestigung an der Unterseite nicht mehr als 5, 08 mm betragen. Als Versorgungsspannugen werden benötigt: +5V +/- 5% 1, 2A; +12V +/- 5% 2, 0A 4. Alle Arbeiten auf dem Festplattte dürfen nur von Ausgebiletem Serciepersonal durchgeführt werden. [. . . ]