User manual MASTERCRAFT X-STAR WAKEBOARD 2001

[. . . ] If you use another power supply cord, it may cause interference with radio and television reception. DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE. CAUTION Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/ Data Processing Equipment, ANSI/NFPA 75. EN-2 Contents Important safeguards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Preparing your projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Using the remote control. [. . . ] MIRROR Select when viewing images projected from the behind of the screen with the projector installed on the floor. INVERT Select when viewing images projected from the behind of the screen with the projector installed on the ceiling. MIRROR INVERT Select when viewing images from the front with the projector installed on the ceiling. LENS LOCK ENTER The LENS LOCK menu is displayed for the following settings. ZOOM/FOCUS LOCK ON / OFF Use to enable or cancel the FOCUS LOCK and ZOOM LOCK. LENS SHIFT LOCK ON / OFF Use to enable or cancel the LENS SHIFT LOCK. LENS SHIFT RESET OK Use to reset the position of the lens to the factory setting. MANUAL Use to adjust the amount of transmission signal correction when a long DVI cable is used. • Regardless of the setting of LAMP MODE, the LOW lamp mode is activated by default whenever the projector is turned on. When LAMP MODE has been set to STANDARD, the lamp mode changes from LOW to STANDARD about 2 minutes after turn-on. • When the ambient operating temperature is high, the brightness of the lamp isn’t changed by switching the lamp mode. • When 7. 5% is chosen, the brightness is decreased by the setup cancel function for the U. S. Choose ON when connecting the projector with a device equipped with the SCART terminal that can output RGB signal. (Available only for the input signal from the COMPUTER/COMPONENT/VIDEO IN 1 terminal. ) When the lamp operating time exceeds 3000 hours with LAMP MODE set to LOW, a warning dialog is displayed. When the lamp operating time exceeds 3800 hours with LAMP MODE set to LOW, a warning dialog is displayed. The no-signal dialog, input dialog, SCART warning dialog, auto power-off dialog, lamp warning dialog, and abnormal temperature dialog aren’t displayed. The menu settings are reset to the factory defaults (except the LANGUAGE, PASSWORD FUNCTION, IMAGE CAPTURE, and NETWORK settings). SCART INPUT ON / OFF LAMP WARNING STANDARD SHORT TERM HIDE OSD OFF ON OK RESET ALL • CINEMA MODE can be adjusted only when a TV60, TV50, 480i, 576i or 1080i signal is being displayed. • When SCART INPUT is set to ON, normal computer signals aren’t projected. • Use a commercially available SCART-Mini D-SUB 15-pin cable when connecting this projector with an AV device equipped with the SCART terminal. • Some AV devices equipped with the SCART terminal aren’t compatible with this projector. • The RESET ALL process may take some time to complete. EN-35 Menu operation (continued) SIGNAL menu opt. opt. SIGNAL A U H V SIGNAL AUTO 1024 x 768 0 0 0 0 AUTO 100% ON ENTER SIGNAL USER 60. 00 Hz 48. 36 KHz 1024 768 OK OK ? MEMORY CALL RESOLUTION (MEMORIZE ) HORIZ. [. . . ] • Contact your dealer. Steady red Blinking green Off *1: Duration when LAMP MODE of the INSTALLATION menu is set to LOW. When it is set to STANDARD, this duration will be shorted up to 3000 hours. *3: When you press the POWER button on the projector or the remote controller, the STATUS indicator blinks red three times and then resumes red illumination. *4: Status of either or both of the indicators. EN-62 Specifications The specifications and outside appearance of the projector are subject to change without prior notice. Type Model Display technology Projection lens Light-source lamp Image size (projection distance) Maximum resolution Computer signal Video signal Component signal Computer/component video input LCD projector X-STAR WAKEBOARD 0. 75-inch LCD panel: 3 pieces (for R, G, B) Pixel: 1280 x 800 = 1024000 pixels Total 3072000 pixels Active pixel rate: 99. 99% or more (each panel) F 1. 8 - 2. 6 f= 24. 0 - 43. 2 mm 321 W 40” min. [. . . ]