User manual MASTERCRAFT X-7 2002

[. . . ] 36 3. 2 Your environmental care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GET TO KNOW YOUR APPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 4. 1 Description of the controls on the front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AVAILABLE ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] USING THE COOKING HOB 6. 1 General warnings and advice Before lighting the hob burners, make sure that the flame-spreader crowns are correctly positioned in their housings with their respective burner caps. 6. 2 Lighting the hob burners All the appliance's control and monitoring devices are located together on the front panel. Simply press the knob and turn it anti-clockwise to the maximum flame symbol until the burner lights. If the burner does not light in the first 15 seconds, turn the knob to “0” and wait 60 seconds before trying again. After lighting, keep the knob pressed down for a few seconds to allow the thermocouple to heat up. The burner may go out when the knob is released: in this case, the thermocouple has not heated up sufficiently. Wait a few moments and repeat the operation, keeping the knob pressed for longer. If the burners should go out accidentally, a safety device will be tripped, cutting off the gas supply, even if the gas tap is open. In this case, turn the knob to the OFF position and wait at least 60 seconds before trying to light the burner again. 6. 3 Practical hints for using the hob burners For better burner efficiency and to minimise gas consumption, use pans with lids and of suitable size for the burner, so that flames do not reach up the sides of the pan (see point “6. 4 Pan diameters”). Once the contents come to the boil, turn down the flame far enough to ensure that the liquid does not boil over. If any liquid does boil over or spill, remove the excess from the hob. To prevent burns or damage to the hob during cooking, all pans or griddles must be placed inside the perimeter of the hob. If the burner does not ignite after 15 seconds, stop attempting to light it, leave the oven door open and do not try to light it again for at least 1 minute. 7. 7. 2 Manual ignition In the event of a power failure, the oven can be ignited manually. Open the oven door fully, press and turn the thermostat knob anti-clockwise between MIN and MAX; light a long match and put the flame through the centre front slots at the bottom of the oven (as indicated in the figure). After lighting, keep the knob pressed down for a few seconds to allow the thermocouple to heat up. If the burner does not ignite after 15 seconds, stop attempting to light it, leave the oven door open and do not try to light it again for at least 1 minute. If the burner is extinguished accidentally, a safety valve will be activated to interrupt the flow of gas. To light it again, first turn the knob to the OFF position ( following the normal procedures. Then relight the gas 7. 8 Using the electric grill Use the function selection knob to select either the grill or the fan-assisted grill. The bottom burner and the electric grill can never be used at the same time. • • Grilling processes must never last more than 60 minutes. Accessible parts may be very hot during and after use of the grill; keep children well away from the appliance. 44 Instructions for the user 8. [. . . ] This type of installation can be used for both built-in and free-standing appliances. Make the connection to the gas mains using a continuous wall flexible steel hose whose specifications comply with the applicable standard. Carefully screw the connector 3 to the appliance’s gas connector 1 (½” thread ISO 228-1), placing the seal 2 between them. Apply insulating material to the thread of the connector 3, and then tighten the flexible steel hose 4 to the connector 3. 1 2 3 4 54 Instructions for the installer 11. 6 Electrical connection Make sure the voltage and the cross-section of the power supply line match the specifications indicated on the identification plate positioned on the appliance. [. . . ]