User manual MARMITEK ROBODOME 10 QUICK INSTALLATION GUIDE

[. . . ] RoboDome10 Outdoor IP Camera housing with heater and fan Quick Installation Guide 20280/20100707 RoboDome10TM © ALL RIGHTS RESERVED MARMITEK®2008 2 ©MARMITEK SAFETY WARNINGS x x All the safety and operating instructions should be read before the units is operated. The wiring of your electrical installation is live (230 V) and extremely dangerous. Precautions for anti-lightning and anti-surging should be taken if necessary. [. . . ] Marmitek does not accept responsibility in the case of improper usage of the product or when the product is used for purposes other than specified. Marmitek does not accept responsibility for additional damage other than covered by the legal product responsibility. Keep out of reach of children. x x x x x x x RoboDome 10 3 INTRODUCTION The dome housing of the RoboDome10 is rain and dustproof to protect your IP RoboCam IP Camera from adverse environment conditions. RoboDome10 has 2 brackets to make it suitable for the installation on different locations. The heater has two elements so that it can operate as a heater and defroster. Cable entry is from cable glands located conveniently on the top plate. The Style of the Installation 1) Dimension of the Product 2) The Style of Installation 2. 1 ) Wall Installation 2. 2 ) Ceiling Installation 4 ©MARMITEK 2. Steps of Installation (taking wall-installing style as example): 1) Unpack the carton and carefully take out the attachments. 4) Fix the bracket on the wall (see Figure 3). 5) Rotate the vitreous cover counter clockwise and take it out (see Figure 4). Install the ball on the bracket (Figure 6). RoboDome 10 5 2. 1 Structure diagram of installation (Figure 6): 2. 2 Structure diagram of pedestal assembly (Figure 5): 6 ©MARMITEK 2. 3 Steps to assemble pedestal with IP camera: Step 1 : Link IP Camera power cord and Ethernet cable 1. 1 Pass the IP camera DC jack and Ethernet cable through the dome base: 1. 2 Pass the DC Plug through the dome base: 1. 3 Seal the rubber (Q7: the sealed rubber) back to the dome base. Make sure you also pass the power cord for the housing heater and fan through the sealed rubber. RoboDome 10 7 Step 2 : Pedestal Assembly 2. 1 Fasten the 5cm Hex Nut (Q3: M3 x60) to the base bracket (BR003). 2. 2 Fasten the base bracket (BR003) to the dome base with three Flat Head fasteners (Q1: M4x13). 2. 3 Fasten the bracket (BR002) to the Hex Nut of the bracket (BR003) with three round head fasteners (Q6: M3 x7). 2. 4 And then fasten two 3. 5cm Hex Nut (Q4: M3 x20) to the bracket (BR002). 8 ©MARMITEK Step 3 : Installation of the IP Camera 3. 1 Fix the IP Camera to the upper bracket (BR001). PS: Please use the IP Camera stand's Screw 3. 2 Connect the IP camera to Power & Network. 3. 3 Place the IP camera in the RoboDome10. RoboDome 10 9 3. 4 Fix it to the bracket (BR002) with two round head fasteners (Q6 M3*7) 3. 5 Install the dome cover clock-wisely. Assembly finished. DOME COVER CLEANING To obtain constant clear videos, user should clean the dome cover periodically. Hold the dome cover ring only to avoid direct touch to the acrylic dome cover. The acid sweat mark of fingerprint will corrode the coating of the dome cover and scratch on dome cover will cause vague images. x Use soft dry cloth or the substitute to clean the inner and outer surfaces. [. . . ] Copyright and all other proprietary rights in the content (including but not limited to model numbers, software, audio, video, text and photographs) rests with Marmitek B. V. Any use of the Content, but without limitation, distribution, reproduction, modification, display or transmission without the prior written consent of Marmitek is strictly prohibited. All copyright and other proprietary notices shall be retained on all reproductions. 12 ©MARMITEK RoboDome 10 13 14 ©MARMITEK RoboDome 10 15 16 ©MARMITEK [. . . ]