User manual MARMITEK PROGUARD 800

[. . . ] PROGUARD 800 PROGUARD800 SERIES TM USER MANUAL ENGLISH 20196 / 20070314 · PROGUARD800TM © ALL RIGHTS RESERVED MARMITEK ® Safety Warnings · The wiring of your electrical installation is live (230 V) and extremely dangerous. · This product is for professional use and should be installed by a certified installer. · To prevent short circuits, this product should only be used inside and only in dry spaces. · Do not expose the components of your systems to extremely high temperatures or bright light sources. [. . . ] These features include Two-Way Audio, remote arming/disarming and siren cancel. Two-Way Audio You may use the Two-Way Audio features to check your home in the event of an alarm or as an alternative means of communicating with members of your family. For example, you may wish to call an elderly person who has difficulty reaching the phone. Using its Two-Way Audio features, the control panel automatically picks up the call and you can communicate via its built-in microphone and speaker. 6. 1: Calling your Home You may call your home at any time in order to contact your family, operate your system or check your home while you are away. This feature is available for both regular telephone communication or cellular communication. Making a Call using a Regular Telephone When your security system shares a telephone line with other devices (e. g. telephone handsets, an answering machine or fax), it is important that the control panel distinguish between calls so that it knows when to pick up the relevant call. Wait at least five seconds and dial the number again; on the second ring, the control panel picks up and sounds two tones. Making a Call to the Cellular Communications Module If your system supports cellular communication, the Cellular Communications Module has its own individual telephone number. Therefore, the double call method is not necessary and you may call the control panel directly. Call Procedure To prevent unauthorized attempts to call your control panel, you must enter a user code when calling your home ­ see 7. 3: User Codes, Code 29. Call the control panel either using the double call method or directly (see above); when the control panel picks up, two tones are sounded. Enter the Telecontrol code (Code 29) on your telephone within 15 seconds. Do not enter your user code until you hear the two tones. Any digits entered before the tones are sounded are disregarded by the system. 3. A tone is sounded to indicate that the system is ready to receive commands. ProGuard800TM -19- The following commands are available: · Press "2" for Two-Way Audio. o If the TWA mode is defined as "Simplex" (see 6. 5: Simplex Mode), the audio channel opens in Listen mode (microphone active/speaker mute). · Press "4XX" to turn HA unit #XX ON · Press "5XX" to turn HA unit #XX OFF · Press "6" to disarm the system. · Press "9" to cancel the siren. The commands "3" (Full Arm), "4" (HA On), "5" (HA Off), "6" (Disarm) and "9" (Bell Cancel) can also be executed at any time during a Two-Way Audio session. 4. 5. The duration of the call is an option programmed by your installer. To disconnect before the end of the call, press "*" then "#" on your telephone. Siren Muting The siren is muted during Two-Way Audio communication. At the end of the call, the siren is re-activated (if the Siren Cut-Off has not yet expired). You can cancel the reactivation of the siren by pressing "9" on your telephone during the call. 6. 2: Service Call The Service Call feature enables you to call the monitoring service by pressing one key. To make a Service Call: · Press and hold down the Service Call key for a few seconds. If using Simplex mode, the call is connected in Listen mode ­ see 6. 5: Simplex Mode. 6. 3: Two-Way Audio after an Alarm In the event of Burglary, Fire and Medical alarms, the control panel is able to report the events and then stay on the line. This allows the monitoring service to verify the alarm or provide assistance in the event of an emergency. 6. 4: Two-Way Audio Follow-Me This feature causes the control panel to call you in the event of an alarm so that you may check your family and home. [. . . ] An optional feature that enables users to record messages to be played back by other users. N Non-Controlled Code A user code that does not cause the system to notify the monitoring service when used to arm or disarm. The system only reports if the code is used to disarm after an alarm. O One-Key Arming Panic Alarm Part Arming Perimeter Arming Arming the system without the need for a valid user code. P A user initiated event that alerts the monitoring service in the event of an emergency. An arming method that is designed to activate a certain section of the premises. An arming method that is designed to activate the sensors protecting the doors and windows while enabling residents to move freely on the premises. R Ready Restore The state in which all zones are closed and the system is ready to be armed. [. . . ]