User manual MARMITEK INVISIBLE CONTROL 4

[. . . ] the product should only be repaired or serviced by a qualified expert. Never use old and new batteries or different types of batteries together. Remove the batteries when you are not using the system for a longer period of time. Check the polarity (+/-) of the batteries when inserting them in the product. [. . . ] Plug the power adapter into the back side of the Invisible Control 4TM or insert 4 pieces `AAA' size ALKALINE battery (not included) into the battery compartment with correct polarity. Connect the wire with the two IR LEDs (the IR extender) to the back side of the Invisible Control 4TM. It doesn't matter whether you use the first or the second connection. Place the Invisible Control 4TM within sight and within reach of your remote control (max. Lead the wire with the IR LEDs (the IR extender) to the A/V equipment in such a way that the IR LEDs (transmitters) are on the front of your equipment (e. Test the position of the IR LEDs first, before you stick them onto the sensor. ATTENTION: If you are only using one appliance, then you do not need to use the second IR LED. The Invisible Control 4TM receives the signal from your remote control and transfers it to an electrical signal, which is passed on to the IR LEDs. This means all signals from your remote control are passed on to your equipment. The Invisible Control 4TM can be connected to the mains or can work using just a battery. If you are inserting a battery, the Invisible Control 4TM will automatically switch to stand-by mode after 4 hours, to conserve energy. You can activate the Invisible Control 4TM by pressing a button on your remote control within 50 cm of the receiver. After reactivation, the Invisible Control 4TM can receive all signals from the remote control within a distance of 4 to 8 m, under an angle of 30°. The Invisible Control 4TM will switch to stand-by mode when it has not been used for 4 hours. If you have connected the Invisible Control 4TM to the mains, it will remain switched on. You do not need to activate the Invisible Control 4TM with your remote control first. In a few cases, the Receiver may be disrupted by interference and cannot, therefore, pick up the signals it receives. If this is the case the red light will be continuously illuminated than the Receiver must be relocated. This interference is caused by equipment in the vicinity such as dimmers, energy-saving light bulbs, IR alarms and so on. Invisible Control 4TM does not work with remote controls which use High Frequency signals (such as B&O). [. . . ] Algunas ventanillas IR de los set-top box o de los box sattelite son muy sensibles y fácilmente a sobrecargar. Alcune finestre IR dei set top box e dei box satellitari sono molto sensibili e quindi facili da sovrapilotare. Hereby, Marmitek BV, declares that this InvisibleContro4TM is in compliance with the essential requirements and other relevant provisions of the following Directives: DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment Hiermit erklärt Marmitek BV die Übereinstimmung des Gerätes InvisibleControl4TM den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtliniën: RICHTLINIE 2004/108/EG DES EUROPÄISCHEN PARLAMENTS UND DES RATES vom 15. Copyright and all other proprietary rights in the content (including but not limited to model numbers, software, audio, video, text and photographs) rests with Marmitek B. [. . . ]