User manual MARANTZ VP8600

[. . . ] Model VP8600 User Guide DLPTM Projector CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] Note : When projecting a video image from a device connected to the DVI-D terminal, follow the procedure below. Turn on power of the device connected to the DVI-D terminal of the unit (i. e. For the details of the DVI-D terminal on the device connected with the unit, see the instruction manual of the device. STANDBY FL OFF SCART CONNECTOR DVD Player COMPONENT 1: RGB When connecting the COMPONENT 1 terminal to the RGB HV out terminal, set COMPONENT 1 settings to [RGB]. ( P. 19) 5RCA cable (commercially available) RGB (D-Sub monitor) cable (commercially available) RGB out RGB OUT or or DVI-D out DVI-D out or HDMI out V H R B G MONITOR OUT HD-Video / Satellite / Cable Tuner / DVD Player PC Monitor output RGB OUT RGB out or or DVI-D out DVI-D out DVI-D cable (commercially available) IBM VGA or Compatible PC 8 Advanced Connection You can control total home theater system using PC. ENGLISH Screen External Controller RS-232C cable (straight type, commercially available) 3. 5mm Mini Plug (Mono) (commercially available) 9 INITIAL SETTING Turning on the Power 1. Connect the other end to a wall outlet. Turn on the main power switch. The Power LED blinks (blue) slowly. Adjust the Zoom, Focus and Keystone 1. Use the ZOOM ring (on the projector) to resize the projected image and screen size. Use the FOCUS ring (on the projector) to sharpen the projected image. ENGLISH FOCUS RING ZOOM RING 2. Press the ON button on the remote controller to turn on the projector. The Power LED lights blue and the projector splash screen displays. 3. Press the EXIT button twice to close the OSD. STANDBY ON COMP. 1 COMP. 2 S VIDEO FULL C1 DVI C2 RGB S VIDEO F NORMAL DV1 RGB V N THEATER STANDARD DYNAMIC ZOOM1 THTR STD DYN C-TEMP Z1 ZOOM2 LOW-BRIGHT- HIGH LB HB CT Z2 5. Press the INPUT 3 or INPUT 4 key to select the input signal source. V-MUTE MENU M 4 INPUT V-MUTE MENU 3 INPUT M F FREEZE PIP ON/OFF INPUT SWAP MENU E EXIT CONTRAST CONCON+ BRIGHTNESS BRIBRI+ 5, 6 F FREEZE PIP E EXIT 7 10 Adjusting the Image There are hot keys on the remote control that let you adjust contrast, sharpness, tint, color, brightness. When you press one of these hot keys, a slide bar is overlayed on the source image. Press the EXIT button to close an image slide bar, or press an image hot key to automatically close the current slide bar and open the next. Tint Control 1. Press the TINT+ / TINT­ button. The tint slide bar appears. CONTRAST CONCON+ BRIGHTNESS BRIBRI+ 2. Press the TINT+ / TINT­ button to Contrast Control Use the contrast control to adjust the contrast between light and dark areas of the projected image. increase/decrease the tint. TINT+ TINT- SHA+ SHAPRAESS SHA- TINT+ TINT TINT- COL+ COLOR COL- WHITE PEAK W-PEAK INFO. 3. Press the CON+ / CON­ button. The contrast slide bar appears. F FREEZE PIP ON/OFF INPUT E EXIT 2. Press the CON+ / CON­ button to increase/decrease the contrast. SWAP MENU CONTRAST BRIGHTNESS BRIBRI+ 3. Press the EXIT button to close the contrast slide bar. CONCON+ CON- CON+ SHA+ SHAPRAESS TINT+ TINT COL+ COLOR WHITE PEAK W-PEAK INFO. Color Control Use the color control to adjust the color saturation level. Press the COL+ / COL­ button. The color slide bar appears. CONTRAST CONCON+ BRIGHTNESS BRIBRI+ 2. Press the COL+ / COL­ button to Sharpness Control Use the sharpness control to adjust the image sharpness. The sharpness control is not available in PC mode. increase/decrease the color. COL+ COL- SHA+ SHAPRAESS TINT+ TINT TINT- COL+ COLOR COL- WHITE PEAK W-PEAK INFO. 3. [. . . ] · Use some other electrical device to confirm that the electrical outlet is working. · Ensure a connected notebook computer is configured for an external display. (This is usually done by pressing an Fn-key combination on the notebook. ) ENGLISH Image Problems Problem: No image appears on the screen 1. Turn off all equipment and power up again in the correct order. Problem: The image is blurred 1. [. . . ]