User manual MARANTZ VP11S1

[. . . ] Model VP-11S1 User Guide DLPTM Projector CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] When power is shut OFF, the lamp flashes for about 1 minute before going out. ENGLISH Note: Pixel defects DLP chip is one of the most advanced technologies for consumer products. The DLP chip made by high precision technology, however some pixel defects may be found on the projected image. We are trying our best to control the quality in order to reduce the number of defective pixels. It is almost impossible to have zero pixel defects, even using the most advanced technology. This is not a problem only for Marantz, but all DLP projector manufactures. Therefore we have to note that the warranty does not cover the DLP chip for pixel defects. We appreciate your understandings. !3 !1 STANDBY indicator Lights up green when the projector is on standby. !2 WARNING/LAMP indicator Flashes or lights up when something is wrong with the lamp cover, lamp, fan, or temperature inside the projector. For more information on the error mode, see the "Error Mode List" ( P. 32)  !3 Ventilation holes (intake) !4 Ventilation holes (exhaust) Notes: Do not place anything near the ventilation holes to avoid overheat inside the unit. Do not place your hand or objects near the ventilation holes; the air is coming out. Note: Lamp SHP lamp is one of the most advanced technologies for consumer products. The lamp made by high precision technology, however some lamps might be failing before it reaches its life. And projector's brightness is getting darker along with accumulated lamp usage hours. We are trying our best to control the quality in order to reduce lamp failures. It is almost impossible to have zero failure, even using the most advanced technology. This is not a problem only for Marantz, but all projector manufactures. Therefore we have to note that the warranty does not cover the SHP lamp for lamp failures: explosion, and nonlighting except initial use. And also we have to note that the warranty does not cover the SHP lamp for lamp failures: flickering, and getting darker along with accumulated lamp usage hours. We appreciate your understandings. Projection Lens !4 q Focus ring ( P. 11) Adjust the picture focus. IR sensor y ENTER button Press to enter the selected menu item. w Zoom ring ( P. 11) u INPUT SELECT button ( P. 16) Adjust the size of the projected image. e Lens Shift knob ( P. 12) r / I button ( P. 16) Selects the input signal (COMPONENT 1, COMPONENT 2, S-VIDEO, VIDEO, RGB, HDMI 1 and HDMI 2). Manually adjust the position of the image vertically. i PATTERN button ( P. 11) Projects a focus pattern on the screen. Press to turn the projector ON or STANDBY mode. t MENU button ( P. 19) Display the on-screen menu. o The 3 / 4 / 1 / 2 buttons Control the MENU cursor. 4 Rear and Terminals View Bottom View ENGLISH IR sensor Ventilation holes (exhaust) Ventilation holes (intake) Ventilation holes (intake) x z Lamp cover Lamp cover securing screw Adjustable feet z x Adjustable feet z AC IN ( P. 9) x RGB IN n TRIG. 1(TRIGGER 1) When the unit is turned on, 12V is output. This allows such as a powered up/down screen, whenever the projector is turned on or off. To connect with external devices, use an ordinal 3. 5mm mini-plug (mono) cable. , TRIG. 2(TRIGGER 2) Select ON or OFF at each aspect mode, such as Full, Normal, Zoom, V-Stretch and Through to control screen aspect ratio with powered up/down dual aspect ratio screen. To connect with external devices, use an ordinal 3. 5mm mini-plug (mono) cable. Connect the supplied AC power code. z Adjustment lever ( P. 12) Connect the analog RGB output from an IBM VGA or compatible equipment. Lift the projector and turn the adjustment lever right or left. Then, release the lever, the adjustable feet is locked. c COMPONENT VIDEO IN 1 and 2 Terminals 1 and 2 have each Y, PB/CB, PR/CR terminals. Connect them to the component video output of a video device, AV amp/processor, DVD player, etc. x Screw holes for ceiling mount kit v S-VIDEO IN Connect the S-VIDEO output from a video equipment. m REMOTE IN/OUT By connecting this projector to another Marantz audio component using a supplied System Control cable, you can remotely operate the components as a single system. [. . . ] THE POWER CORD AND WAIT REFER SERVICING TO QUALIFIED SERVICE 60 MINUTES BEFORE CHARGING PERSONNEL. ATTENTION CHAUD : DEBRANCER LE CORD ON D'ALOMENTION ET ATENDER 60 MINUTES AVANT DE CHANGER LAMPE.  For USA Open the cover sheet and remove the two screws (slotted head screwdriver required) MODEL NO. Press on the handle until it folds over and close the cover sheet. ATTENTION : LA LAMPE SOUS HAUTE PRESSION PEUT SI ELLE, N'EST PAS MANIPULEE CORRECTEMENT, CONFIER L'OPERATION A UN PERSONNEL D'ENTRETIEN QUALIFIE. Cover sheet MADE IN JAPAN FABRIQUE AU JAPON For Europe CAUTION VORSICHT : HIGH PRESSURE LAMP MAY EXPLODED IF BEI FALSCHER HANDHABUNG M IMPROPERLY HANDLED. REFER SERVICING KANN DIE HOCHDRUCKLAMPE EXPLODIEREN UBERLASSEN TO QUALIFIED SERVICE PERSONNEL. [. . . ]