User manual MARANTZ VP10S1

[. . . ] Model VP-10S1 User Guide DLPTM Projector CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. For the customers in the USA: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] Note : To project images from a device connected to the DVI-D jack, do as follows. For details on DVI-D jack of the connected device, see the instruction manual of that device. DVD player) connected to the projector's DVI-D jack. RGB (D-Sub monitor) cable (commercially available) ENGLISH RGB OUT or DVI-D out HD-Video / Satellite / Cable Tuner VIDEO IN S-VIDEO IN COMPONENT VIDEO IN 1 Y PB/CB PR/CR COMPONENT VIDEO IN 2 Y PB/CB PR/CR REMOTE TRIG. EXT. OFF ON OUT 2 Monitor output RGB OUT or DVI-D out IBM VGA or Compatible PC DVI-D cable (commercially available) Connecting to a Home Theater System You can control an entire home theater system using a PC and Marantz receiver equipment. To install the below system, contact your nearest Marantz Authorized Dealer or Service Center. VIDEO IN S-VIDEO IN COMPONENT VIDEO IN 1 Y PB/CB PR/CR COMPONENT VIDEO IN 2 Y PB/CB PR/CR Screen REMOTE TRIG. EXT. LIGHT RGB IN DVI-D IN RS-232C 1 OFF ON OUT 2 RS-232C cable (straight type, commercially available) 3. 5mm Mini Plug (Mono) (commercially available) Control Adapter cable (commercially available) REMOTE CONTROL IN External Controller Control Adapter cable (supplied) REMOTE CONTROL OUT Receiver equipment 16 INITIAL SETTING Activating the Power 1. Press the POWER ON button on the remote controller or the POWER button on the projector. The POWER ON indicator on the projector will light up. STANDBY POWER ON PATTERN PATT. N S TA MENU EN TE R V-MUTE O B Y N D ENTER Focusing and Zooming You can adjust the focus and projected image size using the focus pattern. Press the PATTERN button to project the focus pattern on the screen. STANDBY POWER ON PATTERN PATT. MENU RN IN P UT ME S TA V-MUTE N O B Y N D ENTER 2. To focus the pattern, press the 1 / 2 buttons on the remote controller or projector. Tapping the buttons fine-adjusts the focus. Holding the buttons down quickly changes the focus. Adjust the focus so that the focus pattern appears its sharpest, as shown below. 3. To adjust the size of the projected image, press the 3 / 4 buttons on the remote controller or projector. This completes focusing and zooming. 17 ENGLISH EN TE R PAT TER PAT TE N IN P UT ME NU NU PO WE PO R WE R Positioning the Projected Image You can position the projected image on the screen using the "Lens shift" feature in the menu (OSD). (For an explanation of this feature, see "Configuration"  pg. (If you haven't an Input signal, display the focus pattern. ) PATT. 1. Press the MENU button on the remote controller or projector to display the menu. Select "Config" using the 3 / 4 buttons, then press the 2 button. Select "Lens shift" using the 3 / 4 buttons, then press the 2 button. (If you haven't an Input signal at this point, display the focus pattern. ) 4. Position the projected image vertically on the screen using the 3 / 4 buttons on the remote controller or projector. Upward Downward 5. Position the projected image horizontally on the screen using the 1 / 2 buttons on the remote controller or projector. To right ON STANDBY PATTERN INPUT MENU POWER ENTER ING Top view To left 18 WARN EN TE R PAT TE RN IN P UT ME S TA NU N PO D B WE Y R O N ENGLISH 1 1 2, 3, 4, 5 MENU V-MUTE ENTER 2, 3, 4, 5 INPUT ASPECT Side view WARN ING Keystone Correction ENGLISH If the projected image appears trapezoidal in shape, you can correct it using the "Keystone V" and "Keystone H" features in the menu (OSD). 31. ) PATT. 1 1 2, 3, 4 MENU V-MUTE 2, 3, 4 PAT TE RN IN P UT ME S TA 1. 4. Press the MENU button on the remote controller or projector to display the menu. [. . . ] Set the ON/OFF switch in the off position, unplug the AC power cable and then plug it back in. Then, set the ON/OFF switch in the on position and press either the POWER ON button on the remote control or the POWER button on the projector to reactivate power. 39 ENGLISH SPECIFICATIONS ENGLISH Optical characteristics Technology Panel 3-chip DLPTM 0. 8 inch 16:9 1280 x 720 pixels Digital Micromirror DeviceTM P-VIP 250W AC 1. 44 ­ 1. 80:1 (LN10VP32) 1. 80 ­ 2. 40:1 (LN10VP40) 2. 40 ­ 3. 60:1 (LN10VP53) Projection size Light output 60 to 300 inch (when using 16:9 screen) 1200 ANSI LUMEN typical (Lamp Mode : High) 1000 ANSI LUMEN typical (Lamp Mode : Low) General specifications Power requirement Power consumption Standby consumption Chassis isolution Safety AC 100-120V / 220-240V, 50/60 Hz < 380 W < 2. 0 W Class-1 UL60950 CSA C22. 2 No. 60950 EN60950 FCC Part-15 Class-B EN55022 Class-B 20. 1(W) x 26. 5(D) x 12. 8(H) inch 510(W) x 672(D) x 326(H) mm 90. 3 lb (41 kg) 20 to 80% -4°F to 140°F (-20 to +60°C) 5 to 80% 0 to 4, 921 ft (0 to 1, 500 m) Lamp Lens EMC Dimensions Net Weight Operating humidity Storage temperature Operating temperature 50°F to 95°F (10 to 35°C) Input/Output VIDEO IN RCA x 1 NTSC-35. 8 / PAL-4. 43/SECAM Composite video 1. 0Vp-p / 75 ohm S jack x 1 NTSC-35. 8/PAL-4. 43 / SECAM S-video BNC x 1 Y, CB/PB, CR/PR RGB/HD IN DVI-D IN REMOTE CONTROL IN AC IN Trig. 2 Out RS232C D-sub M 15-pin x 1 Analog RGB, Y/PB/PR DVI-D 24-pin x 1 T. M. D. S. compliant (Single link only) Miniature jack type x 1 3-prong grounding type Miniature jack x 2 Output voltage: 12V DC or 0V RS232C receptacle plug x 1 REMOTE CONTROL OUT Miniature jack type x 1 Storage humidity Operating altitude S-VIDEO IN Accessories · · · · · · · · · Lens cap x 1 Remote controller x 1 AA batteries X 2 AC power cable x 1 Color temperature sensor x 1 Attachment for Color temperature sensor x 1 Control adapter cable (mini jack to RCA) x 1 User Guide x 1 Warranty Card (1 copy each for USA, CANADA) COMPONENT VIDEO IN RCA x 1 Specifications and appearance are subject to change without notice. 40 Timing chart System NTSC PAL-B/G SECAM 480/60p 576/50p 1035/60i 1080/60i 1080/50i 1080/48i 720/60p 720/50p 720/48p 540/60p 640x350#1 640x350#1 640x400#1 640x400#1 640x480 640x480#1 640x480#1 640x480#1 800x600 800x600 800x600#1 800x600#1 800x600#1 1024x768 1024x768 1024x768#1 1024x768#1 1024x768#1 Resolution 768x240 960x287. 5 960x287. 5 720x480 720x576 1920x518 1920x540 1920x540 1920x540 1280x720 1280x720 1280x720 1920x540 640x350 640x350 640x400 640x400 640x480 640x480 640x480 640x480 800x600 800x600 800x600 800x600 800x600 1024x768 1024x768 1024x768 1024x768 1024x768 V (Hz) H (KHz) Scan I 59. 94 / 60 15. 73 I 50 15. 63 I 50 15. 63 P 59. 94 / 60 31. 5 P 50 31. 3 I 59. 94 / 60 33. 8 I 59. 94 / 60 33. 8 I 50 28. 1 I 48 27. 0 P 59. 94 / 60 45. 0 P 50 37. 5 P 48 36. 0 P 59. 94 / 60 33. 8 P 70 31. 5 P 85 37. 9 P 70 31. 5 P 85 53. 7 P 60 31. 5 P 72 37. 9 P 75 37. 5 P 85 43. 3 P 56 35. 2 P 60 37. 9 P 72 48. 1 P 75 46. 9 P 85 53. 7 P 43 35. 5 P 60 48. 4 P 70 56. 5 P 75 60. 0 P 85 68. 7 I : Interlaced signal P : Progressive signal Input Signal Signal Video S-Video Component RGB NTSC X X ­ ­ PAL-B/G X X ­ ­ SECAM X X ­ ­ Video 60Hz ­ ­ X X Video 50Hz ­ ­ X X 480/60p ­ ­ X X 576/50p ­ ­ X X 1035/60i ­ ­ X X 1080/60i ­ ­ X X 1080/50i ­ ­ X X 1080/48i ­ ­ X X 720/60p ­ ­ X X 720/50p ­ ­ X X 720/48p ­ ­ X X 540/60p ­ ­ X X 640x350@70Hz ­ ­ ­ X 640x350@85Hz ­ ­ ­ X 640x400@70Hz ­ ­ ­ X 640x480@60Hz ­ ­ ­ X 640x480@72Hz ­ ­ ­ X 640x480@75Hz ­ ­ ­ X 640x480@85Hz ­ ­ ­ X 800x600@56Hz ­ ­ ­ X 800x600@60Hz ­ ­ ­ X 800x600@72Hz ­ ­ ­ X 800x600@75Hz ­ ­ ­ X 800x600@85Hz ­ ­ ­ X 1024x768@60Hz ­ ­ ­ X 1024x768@70Hz ­ ­ ­ X 1024x768@75Hz ­ ­ ­ X DVI ­ ­ ­ ­ ­ X X X X X X X X X X X X ­ X ­ ­ ­ X X ­ ­ ­ X ­ ­ Note #2 #2 #2 #2 #2 #2 VESA#901101 VESA#900601 VESA#900602 VESA#900603A #2 : both of 59. 94 and 60Hz Notes: · The systems marked #1 are not displayed properly. [. . . ]