User manual MARANTZ VP-12S1

[. . . ] R Model VP-12S1 User Guide Video Projector CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning symbol in the triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation mark in the triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. For the customers in the USA: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] · DYNAMIC ­ DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. ­ "DCDi" is a trademark of Faroudja, a division of Sage Inc. ­ "i. LINK" and the "i. LINK" Logo are trademarks. ­ Even if no trademarks are indicated, they are greatly valued. 2 ENGLISH FEATURES PROJECTOR LAYOUT AND FUNCTIONAL OVERVIEW Front and Top t q IR sensor (one for each front or rear) w Lens e Focus ring Adjust the picture focus. r Zoom ring Adjust the size of the projected image. t Adjusters and Adjusters button Adjust the vertical angle of the projector. y Lens Shift adjuster Adjust the image position vertically. Turn left when the image goes down. u POWER key Press to turn the projector on or standby mode. i MENU key Press to display the on-screen menu. o ENTER key Press to enter items in the menu when the menu is displayed on screen. !0 INPUT SELECT key Select an input signal. Every time the key is pressed, the unit toggles between COMPONENT, S-VIDEO, VIDEO, and RGB inputs. ZO OM 26. 5 - 30. 7 mm ENGLISH o i !3 u q !4 !5 !1 !0 w Cus tom q A optics by M INO LT VP-12S1 !6 t y e r !2 !1 FOCUS key Press to display a focus pattern. !2 The 5 / / 2 / 3 keys Control the menu cursor. Press the 5 key for more than three seconds to turn the HIGH BRIGHT mode on. Press the key to turn the HIGH BRIGHT mode off. !3 POWER ON indicator · Lights up when the power is turned on. · Flashes while the projector goes into standby mode for about one minute. !4 STANDBY indicator Lights up when the power is turned on. !5 WARNING/LAMP indicator Flashes or lights up when something is wrong with the lamp cover, lamp, fan, or temperature inside the projector. !6 Ventilation holes Notes: · Do not place anything near the ventilation holes. · Do not place your hand or objects near the ventilation holes; the air coming out is hot. 3 INTRODUCTION Right Side and Rear /7 VP-12S1 v z x c nb /5 /6 z COMPONENT VIDEO IN Y, PB/CB, PR/CR connectors. Connect to the COMPONENT VIDEO output of video equipment or an A/V processor/receiver with a component video loop. /3 . /0 /4 m /2 , /1 /0 TRIG. 1 When the projector is turned on, a 12-volt signal is sent to the equipment connected to the TRIG. 1. This allows automatic triggering of an accessory, such as a powered up/down screen, whenever the projector is turned on or off. When the unit is turned off, there is no voltage in output and when the unit is turned on, 12 V is output. Note: The user cannot use the connector as the power source. x S-VIDEO IN Connect to the S-VIDEO output of a video equipment. c VIDEO IN Connect to the composite video output of a video equipment. /1 TRIG. 2 Either a 12-volt signal or a 0-volt signal is sent to the equipment connected to the TRIG. 2, according to the setting in the OSD menu. Note: The user cannot use these connector; TRIG. 1 and TRIG. 2, as the power source. v RGB IN Connect to the analog RGB output of a computer equipment. b DV IN Connect to the i. Link(DV-SD format) output of video equipment. n OPTICAL Connect to the optical output of video equipment. /2 LIGHT ON/OFF When using light up the connector panel. m AUDIO OUT (DIGITAL) Connect to the audio input of audio equipment. /3 RS232C Connect to the RS232C output of equipment. , REMOTE SW. (EXTERNAL/INTERNAL) When using the MARANTZ REMOTE CONTROL system, select EXTERNAL. Otherwise select INTERNAL. /4 AC IN Connect the supplied AC power code. . REMOTE CONTROL IN/OUT Connect to the REMOTE CONTROL connectors of other Marantz equipment. It is then possible to control the whole system with a single Remote Controller. /5 Lamp cover /6 Lamp cover securing screw /7 Ventilation holes 4 ENGLISH Bottom ENGLISH Ventilation holes Adjuster button Adjuster button Adjusters How to use adjuster and adjuster button. (1) Adjuster button (2) Adjuster PRESS DOWN UP DOWN 5 INTRODUCTION Remote Controller ¡0 THEATER key ¡1 STANDARD key Select the STANDARD picture mode. The key toggles between Standard1, Standard 2, Standard 3, and Standard Default. s a d ¡2 DYNAMIC key Select the Dynamic picture mode. The key toggles between Dynamic1, Dynamic2, Dynamic3 and Dynamic Default. f g h ¡0 ¡3 ¡6 ¡9 ¡7 TM0 PROJECTOR k j l ¡2 ¡5 ¡8 TM1 ¡1 ¡4 ¡3 INFO key Press to turn the information menu on or off. ¡4 FULL key Select FULL mode from four aspect ratio modes. ¡5 NORMAL key Select NORMAL mode from four aspect ratio modes. ¡6 CINEMA key Press to turn the CINEMA mode ­ auto film detection mode ­ on or off. ¡7 THROUGH key Select THROUGH mode from four aspect ratio modes. ¡8 ZOOM key Select ZOOM mode from four aspect ratio modes. ¡9 AUX key Select the AUX IN signal. TM0 FOCUS key Press to display a focus pattern. a POWER ON key Press to turn the projector on. TM1 V-MUTE key Press to mute the picture so that screen gets dark and no image is displayed. s STANDBY key Press to turn the projector off. d 5 / / 2 / 3 keys f COMPONENT key Select the COMPONENT VIDEO IN signal. g S-VIDEO key Select the S-VIDEO IN signal. h VIDEO key Select the VIDEO IN signal. j RGB key Select the RGB IN signal. k ENTER key l MENU key 6 ENGLISH Select the Theater picture mode. The key toggles between Theater1, Theater2, Theater3 and Theater Default. Preparing the Remote Controller ENGLISH 1. [. . . ] Waverley, VIC 3149, Australia Taborstraße 95 / Ladestraße 1, Gebäude Hangartner, A-1200 Wien, Austria P. O. Box 237, 141, Government Avenue, Manama, Bahrein 1078, Ramjoy Mohanja Lane Asadgonj, Chittagong 4000, Bangladesh Brusselbaan 278, 9320 Erembodegem, Belgium Makedonia Blvd. 16, 1606 Sofia, Bulgaria 633 Granite Court, Pickering, Ontario No. 38 Yushan Road, ShiQiao, Pan Yu, Guang Dong, China P. O. Box 5604, Nicosia, Cyprus Sokolska 41, 67902 Rajecko, OKR, Blansko, Czech Republic Dali Allé 1, 9610 Noerager, Denmark P. O. [. . . ]