User manual MARANTZ ST6003

[. . . ] SVENSKA ITALIANO ESPAÑOL NEDERLANDS DEUTSCH FRANÇAIS ENGLISH Tuner ST6003 ENGLISH WARRANTY For warranty information, contact your local Marantz distributor. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz. IMPORTANT When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. [. . . ] If this happens, take the following steps: · Install this unit as far as possible from the tuner or TV. · Set the antenna wires from the tuner or TV away from this unit's mains cord and input/output connection cords. · Noise or disturbance tends to occur particularly when using indoor antennas or 300 /ohms feeder wires. Note: For heat dispersal, do not install this equipment in a confined space such as a book case or similar unit. NAMES AND FUNCTIONS BASIC CONNECTIONS BASIC OPERATION ADVANCED OPERATION TROUBLESHOOTING OTHERS EQUIPMENT MAINS WORKING SETTING Your Marantz product has been prepared to comply with the household power and safety requirements that exist in your area. ST6003 can be powered by 230V AC only. COPYRIGHT Recording and playback of any material may require consent. For further information refer to the following: -- -- -- -- Copyright Act 1956 Dramatic and Musical Performers Act 1958 Performers Protection Acts 1963 and 1972 Any subsequent statutory enactments and orders 0. 1 m or more 0. 1 m or more TUNER ST6003 0. 1 m or more 0. 1 m or more 2 ENGLISH NAMES AND FUNCTIONS DISP SLEEP AUTO TUNED ST NAMES AND FUNCTIONS FRONT PANEL FL DISPLAY q w TUNER ST6003 e !2 !1 !0 o i u y t r q POWER ON/STANDBY button u T-MODE button a DISP (Display Off) indicator f This indicator is illuminated when this unit is in the display off mode. h TUNED indicator When it is pressed, the display window lights up, and the power comes on. When it is pressed again, the display window is extinguished, and goes into the standby status. Press this button to select the auto stereo mode or mono mode when the FM band is selected. (See page 6) s SLEEP timer indicator g STEREO indicator Lights up in red color while standby status. w INFRARED receiving sensor window This button used for tuning in the desired broadcasting stations or to preset in the desired broadcasting stations. d AUTO indicator h Main Information Display This indicator illuminates when the tuner's Auto mode is in use. This window receives infrared signals from the remote control. A variety of information is displayed on this indicator. etc. o BAND button OTHERS e RDS indicator Press this button to switch between FM and AM in the TUNER mode. This indicator illuminates when receiving RDS broadcasts, and flashes during the RDS search. !0 F (Frequency)/P (Preset) button r DISPLAY button Press this button to change the FL display mode. (See page 8) During reception of AM or FM, you can change the function of the UP/DOWN buttons for scanning frequencies or selecting preset stations by pressing this button. t CLEAR button !1 DIMMER button Press this button to cancel the tuner preset station or preset scan tuning. When this button is pressed twice, the display is turned off and the "DISP" indicator lights up. Press this button again to turn on the display again. y MEMORY button !2 SLEEP button This button is used for setting the sleep timer. Press this button to enter the tuner preset memory numbers or station names. (See page 6) 3 TROUBLESHOOTING STANDBY indicator i TUNING/PRESET 34 (UP/DOWN) button This indicator is illuminated when the sleep timer function is active. This indicator illuminates when an FM station is being tuned into stereo condition. ADVANCED OPERATION This indicator illuminates when the tuner receives a sufficiently strong radio signal. BASIC OPERATION BASIC CONNECTIONS a s d f g ENGLISH REAR PANEL BASIC CONNECTIONS w e r t CONNECTING THE AMPLIFIER Use the audio connecting cord to connect the unit with a stereo amplifier or AV amplifier. NAMES AND FUNCTIONS BASIC CONNECTIONS BASIC OPERATION ADVANCED OPERATION TROUBLESHOOTING OTHERS q Cautions: · Do not connect the unit to the PHONO input connectors on the amplifier. · When making the connections, insert the plugs securely into the connectors. Failure to insert the plugs securely may result in noise. ST6003 q FM antenna terminal (75 ohms) r Connect an external FM antenna with a coaxial cable, or a cable network FM source. REMOTE CONTROL IN and OUT connectors (Red) (White) w AM antenna and ground terminals Connect the supplied AM loop antenna. The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna until you hear the best reception. Using the supplied remote control connecting cord, these connectors enable this unit to be connected to a Marantz component equipped with remote control connectors. These connections make it possible to control an entire system that centers on the amplifier or other such component. t AC INLET Audio connecting cord (supplied) e AUDIO OUT connectors The audio signals are output from these connectors. Plug the supplied mains cord into this AC INLET and then into the power outlet on the wall. ST6003 can be powered by 230V AC only. : Signal flow (Red) (White) Marantz Stereo Amplifier PM5003N PHONO GND SPEAKER SYSTEMS MODEL NO. PM5003 R SYSTEM A L REMOTE CONTROL PHONO TUNER CD AUX / DVD RECORDER 1 (CD-R CD-R) RECORDER 2 (MD / TAPE MD TAPE) IN L L L OUT AC IN R R IN OUT IN OUT R R SYSTEM B L Notes: · Do not plug in the mains cord until all connections have been completed. · When making connections, also refer to the operating instructions of the other components. · Be sure to connect the left and right channels properly (left with left, right with right). [. . . ] Release the lock by pressing the same two keys again at the same time for three seconds or more. "F-KEY UNLOCK" will appear in the display, and the keys will unlock. Hissing or buzzing sound is heard on AM Noise from a TV or interference in the Turn off the TV. Booming sound (humming) is heard in AM Signals transmitted over the main cord Insert the plug in the opposite direction. Connection leads to amplifier not made correctly. GENERAL MALFUNCTION If the equipment malfunctions, this may be because an electrostatic discharge or AC line interference has corrupted the information in the equipment memory circuits. [. . . ]