User manual MARANTZ ST6001

[. . . ] Model ST6001 User Guide FM / AM Tuner ENGLISH WARRANTY For warranty information, contact your local Marantz distributor. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz. IMPORTANT When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. [. . . ] Noise or disturbance of the picture may be generated if this unit or any other electronic equipment using microprocessors is used near a tuner or TV. If this happens, take the following steps: · Install this unit as far as possible from the tuner or TV. · Set the antenna wires from the tuner or TV away from this unit's mains cord and input/output connection cords. · Noise or disturbance tends to occur particularly when using indoor antennas or 300 /ohms feeder wires. Note For heat dispersal, do not install this equipment in a confined space such as a book case or similar unit. ENGLISH 7 EQUIPMENT MAINS WORKING SETTING Your Marantz product has been prepared to comply with the household power and safety requirements that exist in your area. ST6001 can be powered by 230V AC only. 7 COPYRIGHT Recording and playback of any material may require consent. For further information refer to the following: Copyright Act 1956 Dramatic and Musical Performers Act 1958 Performers Protection Acts 1963 and 1972 Any subsequent statutory enactments and orders 7 Accessories Check Before use, check the below accessories were included in the package. · Audio connecting cord x 1 7 Do Not Locate in the Following Places To ensure long-lasting use, do not locate the ST6001 where: · Exposed to direct sunlight. · On wobbly, inclined or otherwise unstable surfaces · Radiated heat is blocked such as in cramped audio racks. To ensure proper heat radiation, ensure the below clearance from walls and other equipment. Left 0. 1 m or more FM/AM TUNER ST6001 DOWN ON/OFF TIMER SET STANDBY A B WIDE NARROW POWER ON/STAMDBY · AM loop antenna x 1 · FM indoor antenna x 1 Above 0. 1 m or more TIMER DAILY ONCE TUNED STEREO RDS Right 0. 1 m or more PRESET UP PTY PT TP TA kHz MHz MEMO PRESET CH ANTETTA FM IF BAND TIME ADJ. ST. NAME /DISPLAY TUNING MODE DOWN TUNING UP CANCEL NEXT MEMO FM MODE RDS BAND · Remote Control Connecting Cord x 1 Rear 0. 1 m or more · User Guide x 1 · Registration Card x 1 2 FRONT PANEL !9 @0 !8 !2 !3 DOWN ON/OFF TIMER SET !4 PRESET UP FM/AM TUNER ST6001 TIMER DAILY TUNED STEREO RDS PTY TP TA kHz MHz MEMO PRESET CH STANDBY A B WIDE NARROW POWER ON/STAMDBY ANTETTA FM IF BAND TIME ADJ. ST. NAME /DISPLAY TUNING MODE DOWN TUNING UP CANCEL NEXT MEMO FM MODE RDS BAND q w e r tyu i o !0 !1 !0 NEXT button !5 !6 !7 q POWER ON /STANDBY button This button is used to power on or power standby. This button is used for advancing to the next step during time adjustment or manual filing, etc. w STANDBY indicator This indicator illuminates red when the unit's status is standby. When daily timer is activated, this indicator lights green. !1 MEMO button This button is used for presetting the broadcasting stations. e ANTENNA A/B button This button is used selection of the FM antenna A or B. !2 (Timer) ON/OFF button This button used for engaging the daily timer function. r IF BAND button This button is used for selecting the bandwidth of the FM broadcast. !3 TIMER SET button This button is used for presetting the time when the system is turned on and off every day at a specified time. t TIME ADJ (adjust) button This button is used for adjusting the current time. !4 PRESET 5 (UP/DOWN) button This button used for preset in the desired broadcasting stations. y ST. NAME/DISPLAY button This button is used for displaying the signal strength. FM More than 50dB 25dB-49dB 10dB-24dB Less than 9dB MW/LW More than 75dB 60dB-74dB 50dB-59dB Less than 49dB Condition Signal strength is good Signal strength is marginal Signal strength is poor Loss of the signal !5 FM MODE button This unit automatically switches into the STEREO mode when a FM stereo broadcast is received press this button to change the monaural mode, then the "STEREO" indicator will go out on the display. Press this button slightly longer (for more than 1. 5 second) to file in manually stations name in the preset memory. !6 RDS button When the FM RDS broadcasting is displayed, and it retrieves, this button is operated. (See page 9) u TUNING MODE button This button is used for selecting the manual tuning or the fine tuning mode. Fine tuning mode is available only in the FM band. !7 BAND button This button is used for selecting the FM, MW or LW broadcast. i TUNING 5 (UP/DOWN) button This button used for tuning in the desired broadcasting stations or adjusting the time, or manual tuning, etc. !8 DISPLAY/INDICATOR !9 Antenna A or B indicator @0 FM WIDE or NARROW band indicator o CANCEL button This button is used for canceling the program during manual file or adjusting the on/off time of the timer. 3 ENGLISH PARTS NAMES AND FUNCTIONS PARTS NAMES AND FUNCTIONS ENGLISH FL-DISPLAY a b c TUNED d STEREO RDS e PTY TP TA kHz MHz f MEMO PRESET CH TIMER DAILY h g a TIMER This indicator lights up when the daily timer is activated. Note Due to the FL-DISPLAY specifications, some character dots may be omitted, but this is not a problem and does not affect product performance. (Example) b DAILY timer indicator This indicator lights up when the daily timer is engaged by pressing the TIMER SET button. c TUNED indicator This indicator lights up when a station is properly tuned in. B D I K M N R S d STEREO indicator This indicator lights up when an FM station is being tuned into stereo condition. T V W X Y Z / e RDS indicators These indicators light up when receiving RDS broadcasts. f MEMORY indicator When the MEMO button is pressed, this indicator blinks for about 8 seconds. g PRESET Number indicator Shows the selected preset number. h CHARACTER indicator A variety of information is displayed on this indicator. etc. 4 REAR PANEL FM ANTENNA B 75 FM ANTENNA A 75 AM ANTENNA GND AM LINE OUT REMOTE CONTROL RESET R L q w er t t RESET switch y q FM antenna terminals A/B (75 ohms) Connect an external FM antenna with a coaxial cable, or a cable network FM source. Press this switch gently with the tip of a ballpoint pen or similarly thin object if the tuner does not respond to a button on the front panel. (See page 11. ) w AM antenna and ground terminals Connect the supplied AM loop antenna. The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna until you hear the best reception. y Power cable Connect the cable to a household power outlet (230V AC). e LINE OUT (analog output) connectors The audio signals are output from these connectors. r REMOTE CONTROL connector Using the supplied remote control connecting cord, this connector enable this unit to be connected to a Marantz component equipped with remote control connectors. This connection make it possible to control an entire system that centers on the amplifier or other such component. 5 ENGLISH PARTS NAMES AND FUNCTIONS CONNECTIONS Note Connect the tuner to other equipment in the below sequence to use the tuner. Connect the LINE OUT and REMOTE CONTROL connectors to their corresponding terminals on a stereo amplifier using the provided cords. (Turn power to the stereo amplifier OFF before making the connections. ) 4. [. . . ] ­ If TP received broadcasting is searched, the increase in frequency will be stop and it is asked whether TA will be received or not. ­ If TP and TA turn off while you are receiving the TA, the tuner will search the TA broadcasting again with the FM frequency increasing in 50 kHz steps. 7) CT mode ­ When you select the CT with the RDS button !6, "CT" will blink for about 4 seconds. After 4 seconds, the clock time together with the frequency will be displayed. [. . . ]