User manual MARANTZ SR8001

[. . . ] Model SR7001/SR8001 User Guide AV Surround Receiver CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT 9. This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. [. . . ] At its widest setting, all the sound from the center is mixed into the left and right speakers. This control may help achieve a more spacious sound or a better blend for the front image. RETURN NEXT EXIT 4. TRUBASS: Set the TRUBASS level between 0 and 6 in 1- level increments with the 1 or 2 cursor buttons. TRUBASS produced by the speakers are an octave below the actual physical capabilities of the speakers adding exciting, deeper bass effects. SRS DIALOG: Set the SRS DIALOG level between 0 and 6 in 1increments with the 1 or 2 cursor buttons. This can be popped out of the surround audio effects, allowing the listener to easily discern what the actors say. If "NONE" was selected for the center speaker setting in the SPEAKER SIZE menu, this setting cannot be selected. After you complete this portion of the setup, move cursor to "RETURN" with the 3, 4, 1 and 2 cursor buttons and press the OK/ENTER button. Note: · This parameter can only be set in the CSII mode. Set the CENTER GAIN level between 0. 0 and 1. 0 in 0. 1 level increments with the 1 or 2 cursor buttons. After you complete this portion of the setup, move cursor to "RETURN" with the 3, 4, 1 and 2 cursor buttons and press the OK/ENTER button. Notes: · This parameter can only be set in the NEO:6-Music mode. · If "NONE" was selected for the center speaker setting in the SPEAKER SIZE menu, this setting is disabled. 34 Video settings are made as follows. 1. Select "4. VIDEO SETUP" from the MAIN MENU with the 3/4 cursor buttons and press the OK/ENTER button. 4. VIDEO VIDEO SETUP CONVERT :DISABLE :ENABLE :ENABLE :OUTPUT1 :MAIN NEXT EXIT The SR7001 is equipped to convert video signals for monitor output. This section explains how to set up conversion for each type of video input. 1. TV. AUTO OSD INFO I/P CONVERT HDMI OUT COMPO OUT2 RETURN Note: · When MULTI 1 is selected, video signals converted from the MONITOR OUT 2 terminal are not output. After you complete this portion of the setup, move cursor to "RETURN" with the 3, 4, 1 and 2 cursor buttons and press the OK/ENTER button. Select "4. VIDEO SETUP" from the MAIN MENU with the 3 / 4 cursor buttons and press the OK/ENTER button. Select "VIDEO CONVERT" with the 3 / 4 cursor buttons and press the OK/ENTER button. VIDEO TV DVD VCR1 DSS AUX1 TAPE CD/R AUX2 RETURN : : : : : : : : CONVERT ANA&HDMI ANA&HDMI ANA&HDMI ANA&HDMI ANA&HDMI ANA&HDMI ANA&HDMI ANA&HDMI BACK EXIT 2. 2. Select the desired menu with the 3/4 cursor buttons and press the OK/ENTER button. · VIDEO CONVERT "4-1 VIDEO CONVERT" · TV-AUTO Select the TV AUTO ON/OFF function to enable or disable with the 1 or 2 cursor buttons. (refer to page 46) · OSD INFO Select the OSD information function to "ENABLE" or "DISABLE" with the 1 or 2 cursor buttons. If you select "ENABLE", the SR7001 will display the status of the feature (Volume up/down, input select, etc. . ) on the monitor. Note: · OSD information is not output to Monitor Output of HDMI and Component Video. However, OSD information is output if the Video Convert function is used to output Video or S-Video video signals to Monitor Out of HDMI and Component Video. · IP CONVERT Select the IP CONVERT ON/OFF function to enable or disable with the 1 or 2 cursor buttons. (refer to page 41) · HDMI OUT (This feature is not available on the SR7001. ) This setting is for selecting which output terminal, HDMI 1 or HDMI 2, to output the signal to. Select the output destination with the 1 / 2 cursor buttons. 3. Select "FUNCTION" with the 3 / 4 cursor buttons and set the video conversion mode with the 1 / 2 cursor buttons ANA&HDMI: This mode both up-converts and down-converts analog video signals (Composite Video, S-Video, Component Video). [. . . ] 87. 5 ­ 108. 0 MHz Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . IHF 1. 8 µV/16. 4 dBf Signal to Noise Ratio . . . . . . . . . . . . . . . . . . . Mono/Stereo 75/70 dB Distortion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mono/Stereo 0. 2/0. 3 % Stereo Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 kHz 45 dB Alternate Channel Selectivity . . . . . . . . . . . . . . . . . ± 300 kHz 60 dB Image Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 MHz 70 dB Tuner Output Level . . . . . . . . . . . 1 kHz, ± 75 kHz Dev 800 mV Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 2 [INPUT] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 1 [OUTPUT] GENERAL Power Requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 120 V 60 Hz Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6. 3A (SR7001) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6. 5A (SR8001) Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33. 1 lbs (15. 0 Kg) (SR7001) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33. 1 lbs (15. 0 Kg) (SR8001) - disconnect the plug from the AC line supply after waiting at least three minutes, reconnect the plug to the AC line supply re-attempt to operate the equipment Remote Control Unit RC8001SR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]