User manual MARANTZ SR7400

[. . . ] Model SR7400 User Guide AV Surround Receiver CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. Read Instructions ­ All the safety and operating instructions should be read before the product is operated. [. . . ] After you complete this portion of the set up, move the cursor to "MAIN" with the or cursor buttons and press the OK button. 21 ENGLISH ENGLISH BASIC OPERATION (PLAY BACK) SELECTING AN INPUT SOURCE Before you can listen to any input media, you must first select the input source on the SR7400. VIDEO CONVERT When this function is activated, the video or Svideo signal can be emitted from the video, Svideo or component video output terminal. To activate this function, select VIDEO CONVERT in PREFERENCE menu and set ENABLE. Example : DVD ER SR7400 TV CLEAR MEMORY TUNING F/P MODE DVD VCR DSS TUNER SPEAKERS A/B MULTI MULTI SPEAKER 7. 1CH INPUT AUX2 CD CD-R MD TAPE TV DVD VCR1 DSS/VCR2 AUX1 CD-R TAPE CD TUNER AUX1 AUX2 AMP LIGHT 1 RC1400 Learning Remote Controller 2 Notes : · The component video signal is emitted only from component video output terminal. When the video equipment is connected by component terminal, connect the monitor and SR7400 by the component terminal. · This function is unavailable for the still picture, fast forward and reverse playing of the video component. · If the picture has a noise with this function, the combination of the monitor, SR7400 and the video component may be not compatibile. In this case, VIDEO CONVERT function must be set DISABLE. Notes of OSD menu: · The setup menu can be displayed through all video out (COMPONENT, S-VIDEO, VIDEO). volume setting) are displayed through all video out when the VIDEO CONVERT function are set ENABLE. Note: no setting information is displayed when the signal is emitted from the COMPONENT IN to COMPONENT OUT. volume setting) are displayed through the S-VIDEO or VIDEO out when the VIDEO CONVERT function are set DISABLE. When the S-VIDEO and VIDEO outputs are used simultaneously, the setting informations are displayed through the S-VIDEO out only. 22 ENGLISH ADJUSTING THE MAIN VOLUME VOLUME CH VOL F/P MODE DOWN UP OK 7. 1CH INPUT AUX2 MUTE S-DIRECT CD-R TAPE CD TUNER AUX1 INPUT DIGITAL S-VIDEO VIDEO L AUDIO R PREV GUIDE MENU TEST CH. SEL MUTE EXIT SURR 1 7 1CH 2 ATT 3 SPK-AB SELECTING THE SURROUND MODE Example : AUTO SURROUND M D1 AV SURROUND RECEIVER SR7400 SELECTOR Adjust the volume to a comfortable level using the VOLUME control knob on the front panel or VOL + / ­ buttons on the remote. To increase the volume, turn the VOLUME knob clockwise or press VOL + button on the remote, to decrease the volume, turn counterclockwise or press VOL ­ button on the remote. To select DVD, simply press the DVD button on the front panel or press the DVD button on the remote. After you have selected DVD, simply turn on the DVD player and play the DVD. · As the input source is changed, the new input name will appear momentarily an OSD information on the video display. · As the input is changed, the SR7400 will automatically switch to the digital input, surround mode, attenuation, and night mode status which were entered during the configuration process for that source. · When an audio source is selected, the last video input used remains routed to the VCR1 & DSS/ VCR2 Outputs and Monitor Output. · When a Video source is selected, the video signal for that input will be routed to the Monitor Output jacks and will be viewable on a TV monitor connected to the SR7400. If a component video input is connected to the DVD or DSS component inputs, it will be routed to the Component Video Output. Make certain that your TV is set to the proper input to view the signal. Example : Monitor is connected with the component. SELECT AV SURROUND RECEIVER SR7400 SELECTOR VOLUME D2 D3 CLEAR MEMORY D4 SPEAKERS A/B ENTER MULTI USE PAGE 1234 D5 STANDBY CLEAR MEMORY TUNING F/P MODE DOWN UP TV DVD VCR1 DSS/V POWER ON/STANDBY SPEAKERS A/B SELECT ENTER MULTI MULTI SPEAKER 7. 1CH INPUT AUX2 MUTE S-DIRECT PHONES STANDBY TV DVD VCR1 DSS/VCR2 AUX CD-R TAPE CD TUNER AUX INPUT POWER ON/STANDBY PHONES DIGITAL S-VIDEO VIDEO L AUDIO R CH TUNER CD CD-R VOL MD Notes: · The volume can be adjusted within the range of ­ to 18 dB, in steps of 1 dB. · However, when the channel level is set as described on page 19, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB. (In this case the maximum volume adjustment range is "18 dB - Maximum value of channel level) VIDEO or S-VIDEO or component Monitor is connected with the video or S-video. AV SURROUND RECEIVER SR7400 SELECTOR VOLUME CLEAR MEMORY TUNING F/P MODE DOWN UP SPEAKERS A/B SELECT ENTER MULTI MULTI SPEAKER 7. 1CH INPUT AUX2 MUTE S-DIRECT TAPE AUX1 AUX2 AMP component LIGHT 1 RC1400 Learning Remote Controller 2 STANDBY TV DVD VCR1 DSS/VCR2 AUX CD-R TAPE CD TUNER AUX INPUT POWER ON/STANDBY PHONES DIGITAL S-VIDEO VIDEO L AUDIO R VIDEO or S-VIDEO VIDEO or S-VIDEO (Using the SR7400) To select the surround mode during playback, turn the SELECT knob on the front panel. (Using the remote control unit) To select the surround mode, press the AMP button and press the > button until PAGE1 is displayed. Press the AUTO (D1) button. ADJUSTING THE TONE (BASS & TREBLE) CONTROL. M D1 AV SURROUND RECEIVER SR7400 SELECTOR D2 D3 CLEAR MEMORY D4 USE PAGE 3 SPEAKERS A/B SELECT ENTER MULTI D5 STANDBY TV DVD VCR1 DSS/VC POWER ON/STANDBY PHONES CH TUNER CD CD-R VOL MD TAPE AUX1 AUX2 AMP LIGHT AV SURROUND RECEIVER SR7400 SELECTOR VOLUME 1 RC1400 Learning Remote Controller CLEAR MEMORY TUNING F/P MODE DOWN UP 2 SPEAKERS A/B SELECT ENTER MULTI MULTI SPEAKER 7. 1CH INPUT AUX2 MUTE S-DIRECT STANDBY TV DVD VCR1 DSS/VCR2 AUX CD-R TAPE CD TUNER AUX INPUT POWER ON/STANDBY PHONES DIGITAL S-VIDEO VIDEO L AUDIO R VIDEO component or S-VIDEO During a listening session you may wish to adjust the Bass and Treble Control to suit your listening tastes or room acoustics. The signal cannot be converted from the component to the video or S-video. (Using the SR7400) To change the selector mode , press the SELECT button, until "BASS" or "TREBLE" is shown on the front display. [. . . ] ± 20 kHz 70 dB ACCESSORIES Remote Control Unit RC1400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 AAA-size batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FM Feeder Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 FM Antenna Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]