User manual MARANTZ SR5004

[. . . ] SVENSKA ITALIANO ESPAÑOL NEDERLANDS DEUTSCH FRANÇAIS ENGLISH AV Surround Receiver SR6004 SR5004 ENGLISH WARRANTY For warranty information, contact your local Marantz distributor. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz. IMPORTANT When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. [. . . ] Watch the picture on the image device (i. e. , TV, monitor, projector, etc. ) as you adjust the time lag. USING THE SLEEP TIMER DUAL BACKUP MEMORY The unit stores settings information in nonvolatile memory even when the main power supply is turned off. Using the Dual Backup Memory function, you can write settings information to another memory area to back up saved settings for recovery anytime as needed. RECOVERY OF MEMORY Recover backed up settings as follows. Hold the MEMORY and MENU buttons on the front panel simultaneously for at least 3 seconds. BACKUP To program this unit for automatic standby, press the SLEEP button on the remote controller. Each press of the button will increase the time before shut down in the following sequence. OFF 120 10 110 100 20 90 30 80 40 70 50 60 Set up the unit in the state for which you want to store the settings. Hold the MEMORY and ENTER buttons on the front panel simultaneously for at least 3 seconds. "MEMORY LOAD" is displayed and the unit's stored settings are reapplied. If there is no backup data, "NO BACKUP" is displayed and no data is recovered. The sleep time will be shown for a few seconds in the display on the front panel, and it will count down until the time has elapsed. When the programmed sleep time has elapsed, the unit will automatically turn off. Note that the SLEEP indicator on the display will illuminate when the Sleep function is programmed. To cancel the Sleep function, press the SLEEP button until the display shows "SLEEP OFF" and the SLEEP indicator will disappear. MEMORY "MEMORY SAVING" is displayed and the unit's settings are saved. The stored settings information is retained until Dual Backup Memory is used again and the information is overwritten. LOAD NO BACKUP MEMORY Note SAVING FRONT KEY (BUTTON) LOCK OF THE UNIT To lock all front panel buttons (except the POWER ON/ OFF button) and the INPUT SELECTER and VOLUME knobs, hold the PURE DIRECT and EXIT buttons on the front panel simultaneously for at least 3 seconds. To unlock the controls, press the same buttons again simultaneously for at least 3 seconds. At this time, "F-KEY UNLOCK" is displayed, and the buttons are released. SURR. MODE PURE DIRECT EXIT CLEAR ADVANCED OPERATION TROUBLESHOOTING OTHERS · The LIP. SYNC feature turns OFF (0 ms) in the SOURCE/PURE DIRECT mode. When the SOURCE/PURE DIRECT mode is deactivated, the set value of the LIP. SYNC feature is automatically restored. · Even if you do not correct the time lag manually this way, audio and video are automatically synchronized when the unit is connected to TV or Projector supporting Auto Lipsync Correction in HDMI 1. 3a. For instructions on Auto Lipsync Correction, see page 35. The following settings values cannot be backed up, each Volume value is set to Minimum. · Main ZONE Volume · ZONE A Volume · ZONE Speaker A Volume 42 ENGLISH NAMES AND FUNCTIONS ADVANCED OPERATION VIDEO CONVERT ANALOG VIDEO CONVERSION This unit is equipped to convert video signals for monitor output. Because of this, indifferent of the connection (VIDEO, S-VIDEO, COMPONENT VIDEO) between the playback device and this unit, listening and viewing are possible with a single higher grade cable between the MONITOR OUT terminal of the unit and the monitor. CONNECTION EXAMPLE · When a monitor is connected to the HDMI MONITOR OUT terminal of the unit · When a monitor is connected to the COMPONENT VIDEO MONITOR OUT terminal of the unit HDMI OUT (SR6004 ONLY) VIDEO or S-VIDEO or component or HDMI HDMI VIDEO or S-VIDEO or component HDMI component UP-CONVERSION FROM ANALOG VIDEO SIGNALS TO HDMI The up-conversion feature of this unit can output the input analog video signals (for component video signals of 480i/576i, 480p/576p, 1080i and 720p resolution, and S-Video and Video (composite) of 480i/576i resolution) to the HDMI MONITOR terminal. Notes · HDMI video input is only output to the HDMI MONITOR OUT terminal of the unit. If connecting a playback device such as a DVD player to the HDMI input jack, connect the HDMI MONITOR OUT terminal of the unit to a TV monitor. · This mode is unavailable for still picture, fast forward and reverse play on video component. [. . . ] 3023 MISSION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3010 MITSUBISHI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3023, 3044 NAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3046, 3047, 3048 NEC MCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]