User manual MARANTZ SR5003

[. . . ] ESPAÑOL FRANÇAIS ENGLISH AV Surround Receiver SR5003 NOTE: - Reorient or relocate the receiving antenna. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Watch the picture on the image device (i. e. , TV, monitor, projector, etc. ) as you adjust the time lag. DUAL BACKUP MEMORY The unit stores settings information in nonvolatile memory even when the main power supply is turned off. Using the Dual Backup Memory function, you can write settings information to another memory area to back up saved settings for recovery anytime as needed. RECOVERY OF MEMORY Recover backed up settings as follows. Hold the MEMORY and MENU buttons on the front panel simultaneously for at least 3 seconds. AUTO POWER ON 1. (Refer to page 37:) Connect your TV TUNER (etc) to the TVVIDEO in terminal. When the station is received, this unit turns ON and TV is selected automatically. BACKUP Set up the unit in the state for which you want to store the settings. Hold the MEMORY and ENTER buttons on the front panel simultaneously for at least 3 seconds. AUTO POWER OFF MEMORY "MEMORY SAVING" is displayed and the unit's settings are saved. The stored settings information is retained until Dual Backup Memory is used again and the information is overwritten. LOAD 1. 2. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast. Note: · The LIP. SYNC feature turns OFF (0 ms) in the SOURCE/PURE DIRECT mode. When the SOURCE/PURE DIRECT mode is deactivated, the set value of the LIP. SYNC feature is automatically restored. · Even if you do not correct the time lag manually this way, audio and video are automatically synchronized when the unit is connected to TV or Projector supporting Auto Lipsync Correction in HDMI 1. 3a. For instructions on Auto Lipsync Correction, see page 38. NO BACKUP MEMORY SAVING Notes: · AUTO POWER OFF is canceled if this unit is set to a source other than TV. · Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON. · The S-Video, component and HDMI terminal does not support "TV AUTO ON/OFF" function. · This function is inactive when STANDBY MODE is set to ECONOMY. To use this function, set STANDBY MODE to NORMAL. Note: · The following settings values cannot be backed up. · Main ZONE Volume · ZONE A Volume · ZONE A Speaker Volume Note: · Because the following settings values are not backed up, each Volume value is set to Minimum. · Main ZONE Volume · ZONE A Volume · ZONE A Speaker Volume 45 ENGLISH VIDEO CONVERT ANALOG VIDEO CONVERSION This unit is equipped to convert video signals for monitor output. Because of this, indifferent of the connection (VIDEO, S-VIDEO, COMPONENT VIDEO) between the playback device and this unit, listening and viewing are possible with a single higher grade cable between the MONITOR OUT terminal of the unit and the monitor. CONNECTION EXAMPLE · When a monitor is connected to the HDMI MONITOR OUT terminal of the unit Notes: · The HDMI video signal input from the playback device is not output from the COMPONENT VIDEO MONITOR OUT terminal of the unit. Notes of OSD menu system: · The setup menu can be displayed through all video out terminals ("HDMI", "COMPONENT", "SVIDEO" and "VIDEO"). · OSD information is output only to the VIDEO and S-VIDEO MONITOR OUT terminals. OSD information is also output when the video conversion feature is on and the video signal input to the VIDEO or S-VIDEO input jack of the unit is converted and output from the COMPONENT VIDEO or HDMI MONITOR OUT terminals. HDMI RESOLUTION This function is used to output the analog video signal to HDMI as follows. [. . . ] 4049, 4050, 4051, 4052, 4053 Janeil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4025 JVC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4017 Mitsubishi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4058, 4059, 4060, 4061 Optima . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]