User manual MARANTZ SR4023

[. . . ] ESPAÑOL FRANÇAIS ENGLISH Receiver SR4023 NOTE: - Reorient or relocate the receiving antenna. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] (Note that the speakers will automatically be turned off when the headphone jack is in use. ) INPUT SELECTOR S. DIRECT DIMMER F/P To select DVD, simply press the DVD button on the front panel or press the DVD button on the remote. After you have selected DVD, simply turn on the DVD player and play the DVD. • When an audio source is selected, the last video input used remains routed to the VCR Output and Monitor Output. This permits simultaneous viewing and listening to different sources. STANDBY PHONES POWER ON/STANDBY During a listening session you may wish to adjust the Bass and Treble Control to suit your listening tastes or room acoustics. (Using the remote control unit) To adjust the bass effect, press BASS 3 or BASS 4 on the remote. To adjust the treble effect, press TREBLE 3 or TREBLE 4 on the remote. Note: When Source Direct mode is set, tone control is disable. 11 OTHERS TROUBLESHOOTING ADVANCED OPERATION Note: The volume can be adjusted within the range of – 90 (∞) to 0 dB, in steps of 1 dB. LISTENING THROUGH HEADPHONES ADVANCED CONNECTIONS Adjust the volume to a comfortable level using the VOLUME control knob on the front panel or VOLUME 3 / 4 buttons on the remote. To increase the volume, turn the VOLUME knob clockwise or press VOLUME 3 button on the remote, to decrease the volume, turn counterclockwise or press VOLUME 4 button on the remote. To temporarily silence all speaker outputs such as when interrupted by a phone call, press the MUTE button on the front panel or MUTE button on the remote. This will interrupt the output to all speakers and the head-phone jack, but it will not affect any recording or dubbing that may be in progress. When the system is muted, the display will show “MUTE ON” . Press the MUTE button again to return to normal operation. BASIC OPERATION BASIC CONNECTIONS VOLUME ENGLISH TUNER OPERATION LISTENING TO THE TUNER Frequency scan step for AM is selectable. Default setup is 10 kHz step, if your country’s standard is 9 kHz step, Press BAND button on the remote controller more than 6 seconds. Scan step will change. MMER MANUAL TUNING (FM) TUNING MODE (AUTO STEREO OR MONO) RECEIVER SR4023 NAMES AND FUNCTIONS BASIC CONNECTIONS BASIC OPERATION ADVANCED CONNECTIONS ADVANCED OPERATION TROUBLESHOOTING OTHERS 1. RECEIVER SR4023 DISP SLEEP MULTI AUTO TUNED DIRECT ST V – OFF NIGHT PEAK ATT EQ AUTO SURR DISC 6. 1 MTX 6. 1 SPKR B 2. DISP SLEEP MULTI AUTO TUNED DIRECT AUTO SURR ANALOG DIGITAL UP ST V – OFF NIGHT PEAK ATT EQ ANALOG DIGITAL SURROUND DISC 6. 1 MTX 6. 1 SPKR B DIGITAL L C R PCM SL LFE S SR DOWN SURROUND DIGITAL L C R PCM SL LFE S SR 2. CL F/P BAND TUNING/ PRESET VOLUME T. MODE MEMORY CLEAR MUTE F/P BAND TUNING/ PRESET T. MODE MEMORY Note: Preset memory for the tuner will clear by changing this setup. 1. When in the auto stereo mode, AUTO indicator will be illuminated on the display. The “ST” indicator is illuminated when a stereo broadcast is tuned in. At open frequencies, the noise is muted and the “TUNED” and “ST” indicators are not illuminated. If the signal is weak, it may be difficult to tune into the station in stereo. In such a case, press the T-MODE button on the front panel or remote controller. “AUTO” indicator is not illuminated, if FM stereo broadcasts are received in monaural and the “ST” indicator is not illuminated. To return to auto stereo mode, press the T-MODE button or press T-MODE button on the remote controller again. AUTO indicator is illuminated on the display. AUTO TUNING 1. RECEIVER SR4023 DISP SLEEP MULTI AUTO TUNED DIRECT ST V – OFF NIGHT PEAK ATT EQ AUTO SURR DISC 6. 1 MTX 6. 1 SPKR B 2. ANALOG DIGITAL (Using the unit) 1. C To select tuner and desired band (FM or AM), press the BAND button on the front panel. Press the TUNING/PRESET 3 or 4 buttons on the front panel to select the desired station. SURROUND DIGITAL L R LFE SL S SR PCM 2. CL 2. MMER F/P BAND TUNING/ PRESET T. MODE MEMORY 1. (Using the remote controller ) 1. 2. (Using the unit) To select tuner and desired band (FM or AM), press the BAND button on the remote controller. Press the TUNE + or – (3 or 4) on the remote controller to tune in the desired station. 1. [. . . ] Mono/Stereo 75/70 dB Distortion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mono/Stereo 0. 2/0. 3% Stereo Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 kHz 45 dB A. C. S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±400 kHz 60 dB Image Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 MHz 70 dB Tuner Output Level . . . . . . . . . . . . . (22 mm) CLEANING OF EQUIPMENT EXTERNAL SURFACES The exterior finish of your unit will last indefinitely with proper care and cleaning, Never use scouring pads, steel wool, scourging powders or harsh chemical agents (e. g. , lye solution), alcohol, thinner, benzine, insecticide or other volatile substances as these wil mar the finish of the equipment. If the equipment get dirty, wipe the external surfaces with a soft, lint-free cloth. If the equipment becomes heavily soiled: • dilute some washing up liquid in water, in a ratio of one part detergent to six parts water. [. . . ]