User manual MARANTZ SR4021

[. . . ] Model SR4021 User Guide Receiver CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT 9. This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. [. . . ] If the transmitter is pointed to a direction other than the IR SENSOR or if there is an obstacle between them, remote control may not be possible. The life of the batteries used with the remote control unit is about 4 months with normal use. Also be sure to replace batteries earlier when you notice that they are getting weak. 1. Remove the back cover. SR4021 pr Ap ox. 5m 2. 60° Insert the new batteries (AAA type) with correct and polarity. Remote control unit (RC4021SR) 3. Close until it clicks shut. 7 ENGLISH THE CONTROLLABLE FUNCTION TABLE USING THE REMOTE CONTROL UNIT PREPARING THE REMOTE CONTROL UNIT FUNCTION AND OPERATION REMOTE CONTROL CODE SETTING The remote control unit contains 3 sets of remote control codes, and it can be used to control up to 3 receivers in one location. To control a second or third receiver, select the remote control code as explained below. · When the unit is shipped from the factory, the main unit and remote control are set to RECEIVER1. ENGLISH CONNECTIONS CONNECTING SPEAKERS System 2 Right Left AMP 1. RECEIVER2 ANTENNA AC OUTLETS 120V REMOTE CONTROL IN To set the remote control to RECEIVER2, hold down both the AMP button and 2 number button on the remote control for at least five seconds. RECEIVER3 To set the remote control to RECEIVER3, hold down both the AMP button and 3 number button on the remote control for at least five seconds. 60Hz AM AUX IN DSS IN VIDEO DVD IN VCR IN OUT MONITOR OUT UNSWITCHED 1. 25A 150W AC IN GND FLASHER IN SWITCHED 1. 25A 150W OUT GND FM (75 ) SYSTEM 1 : MINIMUM 8 OHMS SYSTEM 2 : MINIMUM 8 OHMS R SYSTEM 2 L MODEL NO. SR4021 AUDIO PHONO IN IN OUT IN OUT IN IN IN IN OUT INFO L IN 1, 2, 3 R CD RECORDER 1 (CD-R) RECORDER 2 (TAPE) AUX DSS DVD VCR PRE OUT MAIN IN R SYSTEM 1 L SPEAKER SYSTEMS 2. Also set the main unit's remote control setting to the same setting as the remote control. To change main unit's remote control setting, hold down both the AMP and INFO buttons on the remote control; the remote control setting ("RECEIVER 1", "RECEIVER 2" or "RECEIVER 3") will be displayed in the display window on the main unit and main unit setting will be changed same setting as remote control. CONNECTING SPEAKER WIRE Right Left System 1 1. 3/8inch (10 mm) 2. Caution: · Be sure to use speakers with the specified impedance as shown on the rear panel of this unit. · To prevent damage to circuitry, do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. · Do not connect more than one speaker cable to one speaker terminal. Doing so may damage this unit. Notes · To set the remote control back to RECEIVER1, hold down both the AMP button and 1 number button on the remote control for at least five seconds. · If the batteries in the remote control are replaced while the remote control is set to RECEIVER2 or RECEIVER3, the setting will revert to RECEIVER1. 3. 4. 5. 1. Insert the bare part of the wire into the hole in side of each terminal. Note: Be sure to connect the positive and negative cables for the speaker properly. If they are miss-connected, the signal phase will be reversed and the signal quality will be corrupted. 8 Turn table ANTENNA Graphic equalizer or processor L R AM AUX IN OUT IN L R GND RL GND FM (75 ) RL AUDIO PHONO IN L IN IN OUT IN OUT IN CD player R CD RECORDER 1 (CD-R) RECORDER 2 (TAPE) AUX LR LR VIDEO DVD IN IN VCR OUT MONITOR OUT REMOTE CONTROL IN CD recorder OU Tape Deck IN IN OUT DVD VCR PRE OUT MAIN IN The output audio signal from the RECORDER 1 OUT jack and the RECORDER 2 OUT jack is the same signal which is currently selected. Caution: · Do not connect this unit and other components to mains power until all connections between components have been completed. Red connectors are for the R (right) channel, and white connectors are for the L (left) channel. · Refer to the instructions for each component that is connected to this unit. · Do not bind audio/video connection cables with power cords and speaker cables this will result in generating a hum or other noise. Connecting with external power amplifier This receiver has enough power for normal listening but PRE OUT jacks are prepared to connect external power amplifiers for higher power output. In such a case, connect these jacks to the MAIN IN jacks or AUX IN jacks of the power amplifier. Connecting with graphic equalizer Use PRE OUT and MAIN IN jacks to connect a graphic equalizer or other analog audio processor. Note: When not used, leave these jacks connected with the supplied connecting pins. 9 ENGLISH CONNECTING AUDIO COMPONENTS CONNECTING PRE OUT/MAIN IN JACKS CONNECTING VIDEO COMPONENTS VCR Monitor CONNECTING THE REMOTE CONTROL JACKS ENGLISH ANTENNA AM AUX IN DSS IN VIDEO DVD IN IN VCR OUT MONITOR OUT REMOTE CONTROL IN GND AUDIO OUT LR AUDIO VIDEO IN OUT IN LR VIDEO IN CVBS OUT GND FM (75 ) AUDIO PHONO IN L IN IN OUT IN OUT IN IN IN IN OUT L R L R R CD RECORDER 1 (CD-R) RECORDER 2 (TAPE) AUX DSS DVD VCR PRE OUT MAIN IN LR LR ANTENNA REMOTE CONTROL VIDEO REMOTE CONTROL IN CD recorder REMOTE CONTROL IN OUT CD player REMOTE CONTROL IN OUT DVD PLAYER DV4600 STANDBY DVD player POWER ON/STANDBY VIRTUAL FL OFF IN OUT EXTERNAL INTERNAL OPEN/CLOSE AM AUX IN DSS IN DVD IN IN VCR OUT MONITOR OUT GND EXTERNAL INTERNAL EXTERNAL INTERNAL OU GND FM (75 ) MODEL NO. AUDIO PHONO IN L IN IN OUT IN OUT IN IN IN IN OUT R CD RECORDER 1 (CD-R) RECORDER 2 (TAPE) AUX DSS DVD VCR PRE OUT MAIN IN LR RL LR LR LR q You can control other Marantz products through this unit with the remote control by connecting the REMOTE CONTROL terminals on each unit. The signal transmitted from the remote control is received by the remote sensor on this unit. [. . . ] This function provides approximately one week of memory storage. HOW TO RESET THE UNIT RECEIVER SR4021 MULTI JOG VOLUME 1 SPEAKERS 2 DISPLAY OFF DOWN CLEAR MEMORY BAND F/P AUTO TUNE T-MODE UP BASS TREBLE BALANCE 1 SPEAKERS 2 MUTE SOURCE DIRECT Incorrect Audio or Video for selected source. Sound is only heard from one of front speakers FM or AM reception fails. SLEEP DIMMER RECORDER STANDBY PHONO CD TUNER 1 2 AUX VCR DSS DVD POWER ON/OFF PHONES Noise is heard during AM reception. Cannot get programmed station when the PRESET button is pressed. Reception is affected by other electrical fields. Preset data has been erased. Should the operation or display seem to be abnormal, reset the unit with the following procedure. [. . . ]