User manual MARANTZ SA7003

[. . . ] SVENSKA ITALIANO ESPAÑOL NEDERLANDS DEUTSCH FRANÇAIS ENGLISH Super Audio CD player SA8003 SA7003 ENGLISH WARRANTY For warranty information, contact your local Marantz distributor. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz. IMPORTANT When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. [. . . ] "1", "RPT" indicators will light and the track will be played repeatedly. 2. Up to 24 tracks to be played can be programmed. 1. tO eXIt FrOm ONe tracK repeat · Total remaining time (The remaining playing time from the playing point to the end of the last track) "REMAIN TTL" is displayed Press PROGRAM button on the remote in stop mode. "PROG" indicator will blink and it goes to program mode. Lights up Press the REPEAT button on the remote control twice. "1" "RPT" indicator will disappear, repeat mode will be off and it returns to normal play mode. all tracK repeat When "Repeat" mode is off, press the REPEAT button on the remote control twice. The "RPT" indicator will light up and all track repeat play begins. tO eXIt FrOm raNdOm plaY aNd returN tO NOrmal plaY Press the 7 button, and then press the RANDOM button while playback is stopped. The RNDM (random) indicator goes off, and random play is released. 2. Choose a track to be programmed with numeric buttons on the remote. (Example: The 15th track is chosen and it's length is 4min30sec) Lights up Track information does not appear when "Total remaining time" is displayed. tO returN tO NOrmal plaY Press the REPEAT button on the remote control once. "RPT" indicator will disappear, repeat mode will be off and it returns to normal play mode. Note: Random Play and AMS Play cannot be conducted when the unit is in Repeat Mode. 1st track programmed 14 ENGLISH 3. With the sequence described in step 2 above, program another track. (Example: The 7th track is chosen and total length of 7th and 15th is 7min50sec) tO cHecK tHe prOGrammed tracKs CLEAR tO delete a prOGrammed tracK 4. Press 2 button to starts playback in programmed order. 1. 2. Press CLEAR button in stop mode when program has been made (When "PROG" indicator is lighting up). Every time press CLEAR button, the programmed tracks are deleted in order from the last track programmed. 1. Press S. MODE button in stop mode (not playing). (CD or Super Audio CD) If S. MODE button is pressed again, a playable layer or area will be shown, and the layer or area will be switched to new one. · The sound mode cannot be changed for Audio CDs and discs with only a Super Audio CD area. · The sound mode on hybrid layer discs will be changed in the following order. Super Audio CD stereo area Repeat Play, Random Play, and AMS Play cannot be conducted while the unit is in PROGRAM mode (i. e. when the PROG indicator is lit). tO clear WHOle prOGram Press 7 STOP button two times while in program play. Program can also be cleared by pressing 0 OPEN/ CLOSE button to open the disc tray. tO add tracKs tO prOGram Tracks can be added to the end of program when program is remaining ("PROG" indicator is lighting up) and in stop mode. please Be careFul aBOut tHe FOllOWING matters · When programming 1st through 9th tracks in a disc that has over 10 tracks by using numeric buttons. For instance, programming the 3rd track after programming the 1st track, press 3 button more than approximately 1. 5 seconds after 1 button is pressed. Once you find a song that you want to listen to, press the AMS button again or press the 2 button. The PLAY indicator lights up and normal playback resumes from the current track. Note: AMS Play cannot be conducted while the unit is in PROGRAM mode. CD layer 2. Press the S. MODE button during playback. (CD or Super Audio CD) If S. MODE button is pressed again, the playback is stopped, and the layer or area will be switched to new one. [. . . ] In CD recorders, the task of writing TOC information is referred to as finalizing the disc. Discs that are not finalized cannot be properly recognized as an Audio CD and played back by regular CD players and Super Audio CD players. For details, please read the instruction manual provided with a CD recorder. * TOC stands for Table Of Contents and contains information such as the total number of tracks and total playing time of the disc. [. . . ]