User manual MARANTZ SA-7S1

[. . . ] Model SA-7S1 User Guide Super Audio CD Player CLASS 1 LASER PRODUCT LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT ENGLISH WARRANTY For warranty information, contact your local Marantz distributor. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz. IMPORTANT When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. [. . . ] (See page 18) button button button ¤3 PLAY ¤2 A-B (A-B Repeat button) This button is to determine starting and ending points for A-B repeat play. (See page 16) RANDOM OPEN/CLOSE The buttons listed above are the same to the buttons on the front panel of the main unit. Please see the correspond items in "Front Panel" section. button This button is for random play. (See page 17) * In this instruction manual, some operations can only be performed with the remote control. For operations that can be performed with buttons both on the main unit and on the remote control, the button names are shown in the mark. And for operations that can only be performed with buttons on the remote control, the button names are shown in the mark. 7 ENGLISH NAMES AND FUNCTIONS NAMES AND FUNCTIONS ¤4 AMS ENGLISH (Automatic Music Scan button) Use this button for AMS play. (See page 18) ¤5 REPEAT button This button is for repeat play. "All Repeat" "Track Repeat" "Repeat Off" (See page 16) ¤6 MENU button and ENTER button (Menu setup) These buttons are used to set the time for quick replay. (See page 19) ¤7 QUICK REPLAY (Quick replay) button This button is used to do quick replay of the tracks. (See page 19) ¤8 NOISE SHAPER button This button is pressed to turn the noise shaper on and off. (See page 14) ¤9 DC FILTER button This button is pressed to turn the DC filter on and off. (See page 14) <0 FILTER button This button is pressed to make the digital filter settings. Each time it is pressed, the settings cycle from FIL1 FIL2 FIL3 FIL1. (See page 15) <1 DIGITAL OUT button This button is pressed to turn the digital output for the Audio CD signal on and off. (See page 14) <2 INPUT button This button is pressed to switch the input when using one of the supported Marantz amplifiers (supported models as of September 2006: SC-7S2, PM-11S1, PM-15S1, PM7001, PM7001KI, SR9600). <3 VOLUME button This button can be used to adjust the volume when a Marantz amplifier that has a remote control is used. 8 REAR PANEL A B C D E F A ANALOG OUTPUTS UNBALANCED connectors These are the unbalanced output jacks of the analog audio signals. The analog connection cord can be connected to the CD, AUX, or other connectors on an amplifier. Be sure to connect the L and R channels correctly to the corresponding jacks. * Never connect to the PHONO connector on the amplifier. E DIGITAL OUTPUTS OPT. (Optical digital output connector) The audio CD signal being played is output digitally. that has an optical digital input connector using a commercially available square-shaped optical cable. * No signal is output when playing a super audio CD. B ANALOG OUTPUTS BALANCED connectors These are the balanced output jacks of the analog audio signals. A balanced connection cord (available commercially) can be connected to the balanced input jack of the amplifier. [. . . ] Is the amplifier's function or selector switch set to "CD" or "AUX" or such (to whatever you have connected this unit to)?* Occasionally, sound may stop if the equipment is installed near an air conditioning unit or refrigerator. If this problem occurs, either switch the main power off and on again, or press the OPEN/CLOSE button to open and close the tray, then try playing the disc again. * In the case of a CD-R or CD-RW disc, this problem may occur when the conditions under which its data was originally written were substandard or when the quality of the disc itself is poor. [. . . ]