User manual MARANTZ SA-15S2 UPDATED

[. . . ] 10 0:47:10 PM CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury. cAUTION : USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURE OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. [. . . ] 7 Skipping to the previous or next track (Track Skip) listen to a track posterior to the current track ¶ To ¶ To listen to a track prior to the current track If the 4 button is pressed on the unit or the remote controller while playing a track, playback starts again from the start of the current track. Continue to press the 4 button for the same number of times as the number of tracks you want to return. 10 0:47:52 PM OTHERS Press the ¢ button on the remote controller or the unit the same number of times as the number of tracks you want to advance. TROUBLESHOOTING APPLICATION OPERATION Specify track number with numerical buttons (0-9) on the remote controller. ADVANCED CONNECTIONS 0-9 The search is started by holding down the 4, ¢ buttons on the player or the 1, ¡ buttons on the remote control unit during playback. The search speed can be changed by pressing the 4, ¢ buttons on the player or the 1, ¡ buttons on the remote control unit. The search speed changes in 4 steps: 1 → 2 → 3 → 4 → 1. bASIC OPERATION BASIC CONNECTIONS NAMES AND FUNCTIONS BASIC OPERATION ENGLISH ADVANCED CONNECTIONS CONNECTING TO A DIGITAL AUDIO COMPONENT The player has one digital optical output connector and one digital coaxial output connector. You can enjoy digital recording when the player is connected to a CD recorder or other digital recording component. €¢ After connecting, press the DIGITAL OUT button on the remote control while the CD is stopped and set the digital output for the audio CD signal from the DIGITAL AUDIO OUT terminal to ON. Switch the digital output ON and OFF using the button on the remote control. When digital output is switched OFF, “D OFF” lights up on the LDC display. To enjoy better sound quality, switch digital output to OFF when digital output is not in use. Indd 14 NAMES AND FUNCTIONS BASIC CONNECTIONS BASIC OPERATION ADVANCED CONNECTIONS ADVANCED CONNECTIONS APPLICATION OPERATION TROUBLESHOOTING OTHERS Caution: Signals are sent from the Digital Audio Output (Optical and Coaxial) terminals only when playing back audio CDs or the CD layer of Super Audio CDs. 7 Connecting the optical output connector 7 Connecting the coaxial output connector Use an optical digital connecting cable available on the market. 10 0:47:52 PM ENGLISH CONNECTING THE DIGITAL AUDIO INPUT TERMINAL When connected to devices equipped with digital outputs, such as CD transports or MD recorders, the unit can be used as a D/A converter. REMOTE CONTROL CONNECTION Connecting this player to additional Marantz audio equipment using the supplied remote control cable enables remote control of the connected equipment as a single audio system. €¢ When connecting equipment incorporating a remote sensor, connect the “remote control out” connector of the equipment to the “remote control in” jack of the CD player. When doing this, set this player’s switch to “EXTERNAL. € This will stop its remote control IR receiver from operating and the player can now be controlled via the remote control IR receiver of the attached equipment. Note: This unit can input linear PCM signals with sampling frequencies of 32kHz, 44. Please do not input signals other than linear PCM signals (such as CD-ROM, Dolby Digital, DTS, or AAC signals). [. . . ] €¢ Do not wipe the surface in the circumferential direction. * Do not attach pieces of paper or stickers to the label surfaces of the discs. When a disc has a piece of plastic tape or rental CD label with paste protruding from the edge or when a disc still bears traces of sticky tape or adhesive labels, do not attempt to play it. If such a disc is played on the CD player, you may find that you cannot remove it or that some other kind of malfunctioning may occur. [. . . ]