User manual MARANTZ RC-9500

[. . . ] DFU RC9500 Ver1_2. qxd 5/28/2004 10:32 AM Page 1 Model RC9500 User Guide Touch Screen Remote Control DFU RC9500 Ver1_2. qxd 5/28/2004 10:32 AM Page 2 For US and Canada FCC Compliancy: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rule. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses, and can radiate radio frequency energy and , if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is not guarantee that interference will not occur in a particular installation. [. . . ] Once you have found the correct learning distance, do not change it for any other button on that particular remote control. Most commands learn correctly when you press and hold them until the "OK" indicator appears. However, sometimes the RC9500 will say "OK", yet the command will not operate the component properly. If this improves operation, continue to use the "tap" technique for all other buttons on the remote. +/-) have to be learned using the "press and hold" technique. The following buttons can be programmed: Hard and Soft buttons (buttons in the devices and the Device Overview pages). User Guide 28 DFU RC9500 Ver1_2. qxd 5/28/2004 10:33 AM Page 33 Reference You cannot program the buttons in the Device Overview page directly. You have to program them using "Learn device action" function. (see page 30) The RC9500 also offers empty (non-command programmed) control buttons which you can program and label as existing buttons. They are visible in USE mode as grayed-out. Normal Button (Command programmed) Grayed-out Button (Non-command programmed) Programming Touch Screen Buttons 1 Tap and hold the MODE icon in the LOWER TOOL BAR more than 3 seconds. 3 Select the "Learn button" button and then navigate to the device page which contains the button you want to program. 4 Point the device's original remote control to the RC9500's learning eye as shown on page 28. "Learning" will be displayed on the DEVICE OVERVIEW button and the button's color is reversed. 6 Press and hold the corresponding button on your device's original remote control. If the RC9500 has learned the command successfully, "OK" appears on the Device Overview button. If the RC9500 has not learned successfully, you hear a short buzz and "Failed" appears. (see page 32) 29 User Guide DFU RC9500 Ver1_2. qxd 5/28/2004 10:33 AM Page 34 Reference 8 Return to the Mode Menu page by tapping LOWER TOOL BAR. label in the 9 Return to USE mode by pressing the Left Function button labeled "Exit" via the Mode Menu page. Programming The Device Buttons (Device Action) Note When you teach a command as a Device Action, this command will be sent when you select the Device from the Device Overview page. Remember, the only way to NOT issue this command is to reveal the Device Overview page, press and hold the Left or Right Function buttons (now labeled "No IR") and select the device. 1 Tap and hold the MODE icon in the LOWER TOOL BAR more than 3 seconds. 4 Complete steps 4 to 9 in "Programming Touch Screen buttons" on page 29. Instead of tapping a button on the Touch Screen, press the Device button you want to program. Programming the Hard Buttons per Device The Hard buttons are defined as the five hard buttons next right to the Touch Screen (Channel Up/Down, Volume Up/Down, Mute) and the ten buttons below the Touch Screen (Cursor Up, Down, Right, Left, Menu, Enter, Exit, HOME, Left and Right Function buttons). User Guide 30 DFU RC9500 Ver1_2. qxd 5/28/2004 10:33 AM Page 35 Reference Notes · It is possible to teach commands to the LEFT (labeled "Back") and RIGHT (labeled "Ahead") Function buttons on the remote. But those commands can be re-programmed only via a PC using the editor software. · It is not possible to teach commands to the HOME button on the remote. [. . . ] How can I edit macros that are programmed in the button of the Device Overview?You can do this using "Macro to device" function via the MACRO mode. You can do this using "Label device" function via the LABEL mode. All changes you make to these items are automatically updated in the Device Overview page. [. . . ]