User manual MARANTZ RC-600PMD

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the RX-77 RF Extender. Connect the equipment into an outlet on a different circuit from the receiver. Consult the dealer or an experienced radio/TV technician for help. CAUTION: The user changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. For Europe Declaration of Conformity N° V04ECRC-600PMD: We, Marantz Europe B. V. , PO Box 8744, 5605 LS Eindhoven, The Netherlands declare under our responsibility that the Marantz product described in this user guide is in compliance with the corresponding technical standards such as EN301 489-1 of 2002-08, EN301 489-3 of 2002-08, EN300 220-1 of 2002-09 and IEC60950 of Edition 2001. Eihdhoven, The Netherland Bert Kiggen Marketing manager of Marantz Europe B. V. DFU RC-600PMD Ver1_2. qxd 5/28/2004 10:32 AM Page 3 Dear customer, Please be informed that this carton only contains a copy of the user manual in English. [. . . ] 13 Once you are happy with the macro, press the "Done" button on the screen to save it. 14 Continue to program macros until you have recorded all that you plan. Congratulations!You are now a Home Theater Automator! User Guide 27 DFU RC-600PMD Ver1_2. qxd 5/28/2004 10:33 AM Page 32 Reference 1. Learning IR command You program the Remote Control (RC) commands by transmitting IR (infrared) signals from your existing remote controls to the RC-600PMD's learning IR eye. To do this, place the RC-600PMD and the device's remote control on a flat surface, 1 to 10cm (0. 5 to 3. 6 inches) apart. For each new remote control, you have to find the correct learning distance. 1 to 10 cm apart (0. 5 to 3. 6 inches) It is best to be systematic and teach all of the buttons from one remote control before proceeding to the next. Start with the remotes close together; if you receive a "Failed" message, move them farther apart in one inch increments. Although rare, some component remotes require a very large distance between the sending IR eye LED and the RC-600PMD's learning IR eye. Test the first command from any new remote control to find the correct learning distance. Once you have found the correct learning distance, do not change it for any other button on that particular remote control. Most commands learn correctly when you press and hold them until the "OK" indicator appears. 2 Complete steps 1 to 9 in the programming Touch Screen buttons on page 29. Instead of tapping a button on the Touch Screen, press the hard button you want to program. Note Only via PC, hard buttons can be programmed with a global function for all devices (Programming globally). When a command is learned to a hard button to a device page, it will only be issued when that device is active, even if a command has been programmed globally. Local learning overrides global programming. For example: One could program the CH+ & CH- buttons as the Chapter +/command when the DVD is active. Now, if you program the TV channel +/- globally (and any device other than the DVD is selected) the TV channel +/- commands will be issued. User Guide 31 DFU RC-600PMD Ver1_2. qxd 5/28/2004 10:33 AM Page 36 Reference 2. Labeling Buttons, Pages and Devices The following elements can be labeled: Buttons on a device page and Home page, Page (the name that appears on the Page Overview page), and Device (the name that appears on the Device Overview button and Device Overview page). Labeling a Button 1 Tap and hold the MODE icon in the LOWER TOOL BAR more than 3 seconds. The button you want to label is displayed above the keyboard. Note The frames (texts with non-button function) cannot be labeled on the RC-600PMD. User Guide 32 DFU RC-600PMD Ver1_2. qxd 5/28/2004 10:33 AM Page 37 Reference 6 Edit the label. To delete a character, press the Right Function button labeled "Del". To change the font size, Tap the "+" or "-" buttons beside the "Font" label on the page. Note If the font size does not fit in the button, the font size cannot increase. To enter a character, tap the keyboard near the character you want to use. The keyboard is zoomed in, allowing you to tap exactly the character you need. Repeat this action for every character. Note You can zoom out again without tapping a character by tapping the "Unzoom" button. For capital characters and symbols, tap the "Shift" button repeatedly to display the keyboard you want. Note If you type a longer word than fits in the button, the font size will automatically get smaller. 7 Tap "Enter" button to save the changes. -orPress the Left Function button labeled "Back" to return to the page you were at without saving changes. [. . . ] Error messages If one of the following error messages occurs, please try to update the firmware. Can't open configuration file Configuration file error No configuration file found Invalid configuration file version Tip The bulletin boards and friendly users at www. remotecentral. com can often give you help with problems. Recharging Problems The batteries won't recharge Make sure you are using the rechargeable battery pack, the docking station (DS9500) and the power adaptor supplied with your RC-600PMD. (see page 4) The indicator LEDs on the docking station flashe Check if the contacts on the docking station are clean and free of obstructions. (see page 4) User Guide 61 DFU RC-600PMD Ver1_2. qxd 5/28/2004 10:33 AM Page 66 Frequently Asked Questions Can I program a device button to execute more than one command? [. . . ]