User manual MARANTZ RC-5200

[. . . ] User Guide To The RC9200/RC5200 Touch Screen Remote Controls Automating Your Home Theater With Marantz Automating Your Home Theater With The Marantz RC9200/5200 RC9200/5200 Remote Control User Guide The information in this manual is copyright-protected. No part of this manual may be copied or reproduced in any form without prior written consent from Marantz America, Inc. CORPORATION SHALL NOT BE LIABLE FOR OMISSIONS OR FOR TECHNICAL OR EDITORIAL ERRORS CONTAINED IN THIS MANUAL. SHALL NOT BE HELD LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE SUPPLYING OR USE OF THIS INFORMATION. [. . . ] Commands - When you touch a button, you will record an RC command step (see page 43). Jumps - When you select a device from the Device Menu while holding down the Left hard button (now called device), you will record a panel jump to the last accessed panel of that device (see page 43). Delays - When you select Delay, use the plus and minus arrows to set the amount of delay (see page 44). 25 User Guide Customizing Your RC9200/5200 Note Use the Scroll arrows to navigate; the tab style navigational jumps will not work. If you accidentally record a tab button as a macro step, it will do nothing because you cannot alias to a button that jumps. Since it will confuse you to see it in the Macro Edit window, it is best to delete it. 11 Once all steps have been programmed, test your macro by pressing the right hard button (now labeled Play). Simply putting in lots of delays will make the macro work, but may make the macro unnecessarily long. Try moving commands, so that a TV command alternates with another component command before another TV command is issued. To move a command, simply select it and use the up and down arrows to reposition it within the macro window. If the macro works with a . 5 second delay, try a smaller delay to shorten the macro. When programming Channel macros, use . 1 second delays between different digits and . 5 second delays between identical digits. 13 Once you are happy with the macro, press the left hard button (now labeled Close). 14 Continue to program macros until you have recorded all that you plan. You are now a Home Theater Automator! User Guide 26 Customizing Your RC9200/5200 7. Macros From Your Home Buttons It is possible to program a macro to occur when you select a device (the macro will occur both when you press a home button AND when you select the device from the pull down Device menu). 4 While bracing the RC9200/5200 with your right hand, press and hold the Backlight button with a left hand finger. 6 While still bracing, pressing and holding everything, use a right hand finger to select the device from the Device Menu. 7 The EDIT window appears with the name of your Device at the top of the window. 8 Program your macro following steps 10 through 15 on the previous page. Note In use, you can select a device without issuing the macro by revealing the Device Menu, then pressing and holding the left hard key labeled NO IR, then selecting the device. Otherwise, every time you select the device from home or select it from the device menu, the macro will be sent. User Guide 27 Reference 1. Programming Buttons You program the RC commands (RC for Remote Control) by transmitting infrared signals from your existing remote controls to the RC9200/5200's learning eye. To do this, place the RC9200/5200 and the device's remote control on a flat surface, 1 to 100cm (1/2 to 36 inches) apart. With each new remote control, you have to find the correct learning distance. [. . . ] Carefully press the reset button inside the battery compartment of the RC9200/5200 with a paperclip or sharp pencil. Once the program is installed, open a ccf titled RC9200/5200_Default in C/:Program Files/RCEdit/Samples. Downloading this configuration to your RC9200/5200 will restore your RC9200/5200 to its factory state. The default configuration of the RC9200/5200 takes up almost 1 megabyte of memory leaving approximately 200kb available for your programming. [. . . ]